Steinbach Poolstar Poolrunner S63 Automatic Pool Cleaner User Manual

Introduction

This user manual provides comprehensive instructions for the safe and efficient operation, maintenance, and troubleshooting of your Steinbach Poolstar Poolrunner S63 automatic pool cleaner. Please read this manual thoroughly before using the device to ensure optimal performance and longevity.

The Poolrunner S63 is designed to automatically clean the floor of your pool, saving you time and effort. It is suitable for pools up to 18 m² and also compatible with saltwater pools up to 25 m² of floor area.

Safety Instructions

Always adhere to the following safety guidelines to prevent injury or damage to the device:

• Ensure the power supply is disconnected before performing any maintenance or cleaning.
• Do not operate the cleaner if the power cord or plug is damaged.
• Keep children and pets away from the pool area while the cleaner is in operation.
• Only use the original charger and power adapter provided with the unit.
• Do not use the cleaner in water temperatures outside the specified range of 10°C to 35°C.
• Avoid operating the cleaner in ambient temperatures outside the range of 10°C to 40°C.
• Never attempt to disassemble or repair the unit yourself. Contact qualified service personnel.

Product Overview

The Steinbach Poolstar Poolrunner S63 is an advanced robotic pool cleaner designed for efficient floor cleaning. Below are its key components and features:

Figure 1: The Steinbach Poolstar Poolrunner S63 automatic pool cleaner. This image shows the overall design of the robotic cleaner, featuring its white and dark grey body, four wheels, and a central handle for easy retrieval.

• Main Unit: The core body housing the motor, pump, and filtration system.
• Wheels: Four robust wheels for smooth movement across the pool floor.
• Jet Nozzles: Located at the front and rear, these nozzles propel the cleaner and ensure effective cleaning by stirring debris.
• Control Unit: An external unit with a power cable for controlling the cleaner's operation.
• Dirt Collector: An internal compartment designed to collect debris and dirt from the pool floor.

Figure 2: The Poolrunner S63's movement is controlled via water jet nozzles. This image highlights the cleaner's ability to navigate the pool floor using directed water propulsion.

Figure 3: The external control unit with its power cable. This unit manages the cleaner's functions and connects to the main power supply.

Figure 4: Accessing the large dirt collector. This image shows a hand pressing a latch to open the compartment where collected debris is stored, indicating ease of access for cleaning.

Setup

1. Unpacking: Carefully remove all components from the packaging. Retain the packaging for future storage or transport.
2. Initial Charging: Before first use, fully charge the Poolrunner S63. Connect the control unit to a power outlet and then connect it to the cleaner. The charging indicator on the control unit will show the charging status. A full charge typically takes 5-6 hours.
3. Placement in Pool: Gently lower the Poolrunner S63 into the pool. Ensure it sinks to the bottom completely before activating. Avoid dropping the cleaner into the water.
4. Power Connection: Once the cleaner is submerged, connect the control unit to a suitable power outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for safety.

Operating Instructions

The Poolrunner S63 is designed for simple, automatic operation:

1. Starting the Cleaner: After setup, press the ON/OFF button on the control unit to start the cleaning cycle. The cleaner will begin its automatic cleaning pattern across the pool floor.
2. Cleaning Cycle: The cleaner operates for a predetermined cycle duration, typically around 40 minutes, as observed by users. It navigates the pool floor using its powerful jet nozzles to dislodge and vacuum debris.
3. Optimal Conditions: For best results, ensure the pool water temperature is between 10°C and 35°C, and the ambient air temperature is between 10°C and 40°C.
4. Stopping Operation: To stop the cleaner, press the ON/OFF button on the control unit. Carefully retrieve the cleaner from the pool using its handle.

Figure 5: The Poolrunner S63 actively cleaning the pool floor. This image demonstrates the cleaner submerged and performing its automated cleaning function.

Maintenance

Regular maintenance ensures the longevity and efficiency of your Poolrunner S63:

• Emptying and Rinsing the Dirt Collector: After each cleaning cycle, or when the dirt collector is full, remove it from the unit and empty the collected debris. Rinse the collector thoroughly with clean water.
• Cleaning the Robot: Wipe down the exterior of the cleaner with a soft, damp cloth. Ensure no debris is lodged in the wheels or jet nozzles.
• Filter Maintenance: If your model includes a removable filter, rinse it regularly to maintain optimal suction power.
• Storage: When not in use for extended periods, clean the unit, ensure it is dry, and store it in a cool, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

Here are some common issues and their potential solutions:

If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact customer support.

Specifications

Warranty and Support

The Steinbach Poolstar Poolrunner S63 comes with a warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Steinbach website.

For technical support, spare parts, or any inquiries regarding your product, please contact Steinbach International customer service. Contact information can typically be found on the manufacturer's website or on your purchase receipt.

When contacting support, please have your model number (061007AV) and purchase details ready.