Introduction
This manual provides essential information for the installation, operation, and maintenance of your Lowrance Skimmer Transducers. These transducers are designed to enhance your fishfinding capabilities by providing detailed underwater imaging. Please read this manual thoroughly before installation and use to ensure proper function and longevity of your equipment.
Product Components
Your package includes the following Lowrance Skimmer Transducers:
- Lowrance 000-10802-001 Skimmer Transom Mount Transducer (for LSS-2 StructureScan HD Fishfinder)
- Lowrance 000-0106-72 83/200 kHz Transom-Mount Skimmer Transducer with Built-in Temperature Sensor (for X100C, X125, X135, LMS 330C, LMS 480 Fishfinders)
Image: The complete Lowrance Skimmer Transducer kit, showing both the 000-10802-001 StructureScan transducer (left) and the 000-0106-72 83/200 kHz skimmer transducer (right) with their respective cables and mounting hardware.
Setup and Installation
Proper installation is crucial for optimal performance. Both transducers are designed for transom mounting.
General Transom Mount Guidelines:
- Location Selection: Choose a location on the transom where water flow is smooth and free from turbulence caused by the hull, engine, or other accessories. The transducer face should be fully submerged in water at all speeds.
- Mounting Angle: Ensure the transducer is mounted parallel to the waterline. Adjust the angle to prevent air bubbles from interfering with the sonar signal.
- Drilling: Carefully mark and drill pilot holes according to the provided mounting template (if included with your specific transducer model). Apply marine sealant to all drilled holes to prevent water intrusion.
- Cable Routing: Route the transducer cable away from sources of electrical interference (e.g., engine wiring, VHF radio cables). Secure the cable to prevent damage.
- Connection: Connect the transducer cable securely to the corresponding port on your compatible Lowrance fishfinder unit.
Specific Transducer Notes:
- 000-10802-001 (StructureScan HD): This transducer is typically mounted slightly deeper than the 83/200 kHz skimmer for optimal SideScan and DownScan imaging. Refer to your LSS-2 StructureScan HD Fishfinder manual for detailed placement recommendations.
- 000-0106-72 (83/200 kHz Skimmer): This transducer provides traditional 2D sonar. Its built-in temperature sensor requires full water contact for accurate readings.
Image: The Lowrance 000-10802-001 Skimmer Transom Mount Transducer, designed for StructureScan HD, featuring a longer, streamlined profile.
Image: The Lowrance 000-0106-72 83/200 kHz Transom-Mount Skimmer Transducer with its mounting bracket and cable, featuring a more compact design.
Operating Instructions
Once installed, the transducers will transmit sonar data to your compatible Lowrance fishfinder unit. Refer to your fishfinder's specific user manual for detailed instructions on how to interpret the sonar display and adjust settings.
Key Operational Aspects:
- Power On: Ensure your fishfinder unit is powered on and the transducers are connected.
- Transducer Selection: Some fishfinders allow you to select which transducer is active or to view data from multiple transducers simultaneously. Verify the correct transducer is selected for the desired sonar view (e.g., 2D sonar, StructureScan).
- Sensitivity/Gain: Adjust the sensitivity or gain setting on your fishfinder to optimize the clarity of the sonar returns. Too high can introduce clutter; too low can miss targets.
- Frequency: The 000-0106-72 transducer operates at 83/200 kHz. Higher frequencies (200 kHz) provide greater detail in shallower water, while lower frequencies (83 kHz) offer better depth penetration.
- Temperature Readings: The 000-0106-72 transducer provides water temperature readings directly to your fishfinder display.
Maintenance
Regular maintenance ensures the longevity and performance of your transducers.
- Cleaning: Periodically clean the transducer face with mild soap and water to remove marine growth, dirt, or oil. Avoid abrasive cleaners or tools that could scratch the surface.
- Inspection: Regularly inspect the transducer cable for cuts, kinks, or damage. Check the mounting bracket for looseness or corrosion.
- Anti-fouling: If operating in areas prone to heavy marine growth, consider applying a transducer-safe anti-fouling paint. Consult your local marine supply store for appropriate products.
- Winterization: If storing your boat in freezing temperatures, ensure the transducer is not exposed to ice, which can cause damage.
Troubleshooting
If you experience issues with your transducers, consider the following common troubleshooting steps:
- No Sonar Readings:
- Check all cable connections between the transducer and the fishfinder unit.
- Ensure the fishfinder unit is powered on and the correct transducer is selected.
- Verify the transducer is fully submerged in water.
- Intermittent or Weak Readings:
- Inspect the transducer face for marine growth or damage. Clean if necessary.
- Check for air bubbles or turbulence around the transducer. Adjust mounting position if needed.
- Reduce boat speed to see if the issue resolves.
- Adjust sensitivity/gain settings on your fishfinder.
- Inaccurate Temperature Readings:
- Ensure the 000-0106-72 transducer's temperature sensor is fully submerged and clean.
- Verify the transducer is correctly connected to the fishfinder.
- Distorted StructureScan Images:
- Ensure the 000-10802-001 transducer is mounted correctly and free from obstructions.
- Adjust range and contrast settings on your LSS-2 StructureScan HD Fishfinder.
- If problems persist, consult your Lowrance fishfinder's user manual or contact Lowrance customer support.
Specifications
| Feature | Lowrance 000-10802-001 | Lowrance 000-0106-72 |
|---|---|---|
| Transducer Type | Skimmer Transom Mount (StructureScan HD) | Skimmer Transom Mount (2D Sonar) |
| Frequencies | StructureScan HD (Specific frequencies for SideScan/DownScan) | 83 kHz / 200 kHz |
| Built-in Sensor | None specified | Temperature |
| Mounting | Transom Mount | Transom Mount |
Compatibility
- Lowrance 000-10802-001: Compatible with LSS-2 StructureScan HD Fishfinder units.
- Lowrance 000-0106-72: Compatible with X100C, X125, X135, LMS 330C, LMS 480 Fishfinders.
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation included with your primary Lowrance fishfinder unit or visit the official Lowrance website. Keep your purchase receipt as proof of purchase for warranty claims.
