JIARUIXIN RX97 6V Bluetooth Remote Control and Receiver Kit Instruction Manual

1. Product Overview

This manual provides instructions for the JIARUIXIN RX97 6V 2.4G Bluetooth Remote Control and Receiver Kit. This kit is designed as a replacement part for specific kids' powered ride-on cars, particularly bumper car controllers. It includes one control box and one remote control.

Key Features:

• Weeelye 2.4G Bluetooth Remote Control and Receiver.
• Model Number: RX97 6V CEFC with a 10-pin four-sided socket.
• Designed for 6V powered ride-on car systems.

Figure 1.1: The RX97 6V Bluetooth Remote Control and Receiver Kit, showing both the red remote control and the black receiver unit.

2. Safety Information

For external use only. Keep the control box and remote control away from naked flames or direct heat sources. Ensure all connections are secure before operation. Adult supervision is recommended when children are operating ride-on toys.

3. Setup and Installation

3.1 Verifying Compatibility

Before installation, ensure this control box is compatible with your ride-on car. Open your existing electric ride-on car and locate the control box. Compare its appearance and model number with the RX97 6V CEFC model. The replacement part must have the same appearance and the model number on the side of the control box should match.

Figure 3.1: Side view of the RX97 6V CEFC control box, highlighting the model number label for verification.

3.2 Remote Control Battery Installation

The remote control requires two AAA 1.5V batteries. To install:

1. Use a Phillips screwdriver to unscrew the screw on the back of the remote control.
2. Remove the battery cover.
3. Insert two AAA 1.5V batteries, ensuring correct polarity.
4. Replace the battery cover and secure it with the screw.

Important: Do not mix old and new batteries, or different types of batteries. Remove exhausted batteries promptly.

Figure 3.2: Top view of the red remote control, showing the button layout. The battery compartment is located on the underside.

3.3 Frequency Binding (Pairing)

The remote control and receiver must be paired for the first use or after replacing the remote control batteries.

1. Ensure batteries are installed in the remote control.
2. Press and hold the "M" button on the remote control for 2-4 seconds. The indicator light on the remote will flash.
3. Turn on the power of the ride-on car. The indicator light on the remote control will change from flashing to solid, indicating successful frequency binding.

Figure 3.3: Diagram illustrating the remote control operation manual, including battery installation and frequency binding steps.

4. Operating Instructions

4.1 Remote Control Functions

The remote control features directional buttons and a special function button:

• Up Arrow (▲): Moves the car forward.
• Down Arrow (▼): Moves the car backward.
• Left Arrow (◀): Turns the car left.
• Right Arrow (▶): Turns the car right.
• M Button: Used for frequency binding (pairing).
• P Button (Emergency Braking): Pressing this button will immediately stop the car's running function. Press it again to release the emergency brake and resume normal operation.

4.2 Power Saving Mode

If the remote control is not operated for 10 seconds, its indicator light will turn off, entering a power-saving mode to conserve battery life.

5. Maintenance

To ensure the longevity and proper functioning of your RX97 6V kit:

• Regularly check the battery compartment of the remote control for corrosion.
• Remove exhausted batteries promptly to prevent leakage and damage.
• Keep the control box and remote control clean and dry. Avoid exposure to moisture or extreme temperatures.
• Inspect all wiring connections to the control box periodically to ensure they are secure and free from damage.

6. Troubleshooting

If you encounter issues with your RX97 6V kit, refer to the following common problems and solutions:

• Remote Control Indicator Light Flashes Continuously: This indicates that the frequency binding failed. Remove the batteries from the remote control, reinsert them, and repeat the frequency binding steps (Section 3.3).
• Car Not Responding to Remote Control:
  • Check if the remote control batteries are depleted or incorrectly installed. Replace if necessary.
  • Ensure the remote control and car are properly paired (frequency bound). Repeat Section 3.3.
  • Verify that the car's power is turned on.
• Car Not Moving (Lights On, No Motor/Sound): This often indicates an issue with the control box. Ensure the control box is correctly installed and all connections are secure. If the issue persists, the control box may need replacement.
• Incorrect Voltage Compatibility: Ensure the voltage of the replacement control box (RX97 6V) matches your car's requirements. This model is specifically designed for 6V systems. Using a control box with an incorrect voltage rating will prevent proper function and may cause damage.

7. Specifications

8. Warranty Information

Specific warranty details for the JIARUIXIN RX97 6V Bluetooth Remote Control and Receiver Kit are not provided in the product information. Please refer to the retailer's return policy or contact the seller directly for warranty inquiries.

9. Support

For further assistance or technical support, please visit the JIARUIXIN store page on Amazon or contact the seller through the platform where the product was purchased. Ensure you have your product model number (RX97 6V) and purchase details available when seeking support.