1. Introduction
Thank you for choosing the HOMCOM Floating Bedside Table Set. This manual provides essential information for the safe assembly, installation, and use of your new bedside tables. Please read these instructions carefully before beginning assembly and retain them for future reference.
Image 1.1: The HOMCOM Floating Bedside Table Set installed in a bedroom.
This set includes two wall-mounted nightstands, each featuring a slide-out drawer and an open shelf, designed to save floor space and provide convenient storage for your bedroom essentials.
2. Safety Information
- Read all instructions before assembly and installation.
- Keep all small parts and packaging materials away from children and pets to prevent choking hazards.
- Ensure the wall you intend to mount the tables on is structurally sound and capable of supporting the weight of the tables and their contents. Consult a professional if unsure.
- Use appropriate wall anchors and screws for your specific wall type (e.g., drywall, concrete, wood studs). The provided hardware may not be suitable for all wall types.
- Do not overload the tables. Refer to the 'Specifications' section for maximum weight capacities.
- Periodically check all connections and mounting hardware to ensure they remain tight and secure.
- Avoid placing hot items directly on the surface without protection.
3. Package Contents
Before assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, please contact customer service.
- 2 x Floating Bedside Table Units (disassembled)
- 1 x Assembly Hardware Kit (screws, dowels, wall anchors, etc.)
- 1 x Instruction Manual (this document)
4. Tools Required for Assembly and Installation
The following tools are recommended for assembly and installation:
- Phillips Head Screwdriver
- Drill (with appropriate drill bits for wall mounting)
- Level
- Measuring Tape
- Pencil
- Stud Finder (recommended for drywall installation)
5. Setup (Assembly & Installation)
Assembly is required for each bedside table. It is recommended that one person performs the assembly. Follow the steps below carefully.
5.1. Assembling the Bedside Table Unit
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches. Identify all panels and hardware according to the included parts list.
- Assemble the Main Frame: Connect the side panels to the top and bottom panels using the provided screws and wooden dowels. Ensure all connections are tight and the frame is square.
- Install the Drawer Glides: Attach the drawer glides to the interior side panels of the main frame using the designated screws. Ensure they are level and correctly oriented for the drawer to slide smoothly.
- Assemble the Drawer: Construct the drawer box by connecting the drawer sides, front, and back panels. Slide the bottom panel into the grooves. Attach the drawer glides to the sides of the assembled drawer.
- Insert the Drawer: Carefully slide the assembled drawer into the main frame, aligning the drawer glides. Test the drawer's movement to ensure it opens and closes smoothly.
- Attach the Back Panel: Secure the back panel to the main frame using small nails or screws.
Image 5.1: Detail of the drawer and open shelf, illustrating the storage components.
5.2. Wall Mounting Instructions
Proper wall mounting is crucial for stability and safety. If you are unsure about your wall type or the appropriate hardware, consult a qualified professional.
- Determine Mounting Location: Choose a suitable height and position for your bedside table. Consider the height of your bed and personal preference. Use a measuring tape and pencil to mark the desired location.
- Identify Wall Studs (if applicable): If mounting on drywall, use a stud finder to locate wall studs for maximum security. Mounting directly into studs is highly recommended.
- Mark Drilling Points: Hold the assembled bedside table against the wall at the marked location. Use a level to ensure it is perfectly horizontal. Mark the positions for the mounting screws through the pre-drilled holes on the back of the table.
- Drill Pilot Holes: Using an appropriate drill bit for your wall type and chosen hardware, drill pilot holes at the marked points. If using wall anchors, insert them according to their instructions.
- Attach to Wall: Align the bedside table with the pilot holes/anchors. Insert the mounting screws through the table's back panel and into the wall. Tighten the screws securely, but do not overtighten, which could damage the table or wall.
- Verify Stability: Gently pull on the installed table to ensure it is firmly attached to the wall and does not wobble.
Image 5.2: The floating design allows for easy floor cleaning underneath.
6. Operating the Bedside Table
The HOMCOM Floating Bedside Table is designed for simple and convenient use.
- Drawer Usage: Gently pull the drawer handle to open the slide-out drawer. Push it back in until it is flush with the table front to close. Avoid forcing the drawer if it feels stiff; check for obstructions.
- Open Shelf: The open shelf below the drawer provides easy access storage for books, magazines, or decorative items.
- Tabletop: The flat tabletop can hold items such as lamps, alarm clocks, or beverages. Always use coasters for drinks to protect the surface.
7. Maintenance
Proper care will extend the life and appearance of your bedside tables.
- Cleaning: Wipe the surfaces with a damp cloth. For stubborn marks, use a mild, non-abrasive cleaner. Dry immediately with a clean cloth.
- Avoid Harsh Chemicals: Do not use abrasive cleaners, solvents, or polishes containing silicone, as these can damage the finish.
- Spills: Clean up spills immediately to prevent staining or damage to the engineered wood.
- Hardware Check: Periodically inspect all screws and mounting hardware. Tighten any loose connections to maintain stability.
- Sunlight Exposure: Avoid prolonged exposure to direct sunlight, which can cause fading or discoloration.
8. Troubleshooting
- Table feels wobbly after installation:
- Ensure all mounting screws are securely tightened.
- Verify that appropriate wall anchors were used for your wall type. If not, consider re-installing with stronger anchors or mounting into wall studs.
- Drawer does not slide smoothly:
- Check that the drawer glides are correctly installed and aligned on both the drawer and the main unit.
- Ensure no debris is obstructing the glides.
- Verify that the drawer box is assembled squarely.
- Missing parts or damaged components:
- Refer to the 'Package Contents' section and contact customer service with your model number and a description of the issue.
9. Specifications
| Feature | Detail |
|---|---|
| Model Number | 831-630V81ND |
| Overall Dimensions (each) | 37W x 32D x 21H cm (14.6"W x 12.6"D x 8.3"H) |
| Drawer Inner Size | 29W x 23.5D x 6H cm (11.4"W x 9.3"D x 2.4"H) |
| Open Shelf Size | 34W x 30D x 8.5H cm (13.4"W x 11.8"D x 3.3"H) |
| Material | Engineered Wood (Particle Board with Melamine Finish) |
| Color | Natural Wood Finish |
| Weight Capacity (Total) | 10 kg (22 lbs) per table |
| Weight Capacity (Drawer) | 3 kg (6.6 lbs) per drawer |
| Weight Capacity (Shelf) | 5 kg (11 lbs) per shelf |
| Assembly Required | Yes |
| Number of Items | 2 |
Image 9.1: Detailed dimensions of the bedside table and its components.
10. Warranty and Support
HOMCOM products are manufactured to high-quality standards. For warranty information, specific terms and conditions, or technical support, please refer to the documentation included with your purchase or visit the official HOMCOM website. Please have your model number (831-630V81ND) ready when contacting support.