ECONTROLLY 290P187040 Replacement Remote Control User Manual

1. Introduction

This manual provides essential information for the proper setup, operation, and maintenance of your ECONTROLLY 290P187040 Replacement Remote Control. This remote is designed to function as a direct replacement for various Mitsubishi TV models, offering infrared control without the need for complex programming.

2. Product Overview

The ECONTROLLY 290P187040 is an infrared remote control engineered to provide seamless operation for compatible Mitsubishi televisions. It features a standard button layout for intuitive control of TV functions.

Figure 2.1: Front view of the ECONTROLLY 290P187040 Replacement Remote Control. This image displays the full layout of the remote control, including all buttons for TV, Audio, Power, Channel, Volume, Number Pad, and navigation controls.

Key Features:

Direct replacement for original Mitsubishi TV remote controls.
Infrared technology for reliable communication with your TV.
No programming required; ready to use with compatible models.
Powered by AA ALKALINE batteries (not included).

3. Compatibility

This replacement remote control is compatible with the following Mitsubishi TV models:

WD-73831
LT-46244
WD-57831
LT-52244
LT-37132
WD-65831
LT-46231
LT46244
WD65831
LT37132
WD57831
WD73831
LT52244
LT46231

Please verify your TV model number to ensure compatibility.

4. Setup

4.1 Battery Installation

The remote control requires two (2) AA ALKALINE batteries for operation. Rechargeable batteries are not recommended.

Locate the battery compartment cover on the back of the remote control.
Slide the cover downwards or press the latch (if present) and lift to open the compartment.
Insert two AA ALKALINE batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
Replace the battery compartment cover by sliding it back into place until it clicks securely.

Angled view of the ECONTROLLY 290P187040 Replacement Remote Control

Figure 4.1: Angled view of the remote control, showing the general shape and button layout. The battery compartment is located on the back, not visible in this view.

4.2 Initial Use

This remote control is pre-programmed and does not require any additional setup or coding. Once batteries are correctly installed, it is ready for immediate use with compatible Mitsubishi TV models.

5. Operating Instructions

Point the remote control directly at your Mitsubishi TV's infrared receiver. Ensure there are no obstructions between the remote and the TV.

Common Button Functions:

POWER: Turns the TV on or off.
TV/AUDIO/DVD/VCR: Selects the input source.
Number Pad (0-9): Directly enters channel numbers.
VOL +/-: Adjusts the volume level.
CH PAGE +/-: Changes the TV channel up or down.
MUTE: Silences the TV audio.
ENTER: Confirms selections in menus.
Arrow Buttons (Up/Down/Left/Right): Navigates through menus and options.
MENU: Accesses the TV's main menu.
EXIT: Exits the current menu or screen.
GUIDE: Displays the program guide.
INFO: Shows information about the current program or input.

Refer to your Mitsubishi TV's original user manual for specific functions of advanced buttons if needed.

6. Maintenance

6.1 Battery Replacement

Replace batteries when the remote control's responsiveness decreases or it stops functioning. Always replace both batteries simultaneously with new AA ALKALINE batteries. Do not mix old and new batteries, or different types of batteries.

6.2 Cleaning

To clean the remote control, gently wipe its surface with a soft, dry cloth. For stubborn dirt, slightly dampen the cloth with water. Avoid using harsh chemicals, abrasive cleaners, or excessive moisture, as these can damage the remote.

7. Troubleshooting

Problem	Possible Cause	Solution
Remote control not working.	Dead or incorrectly installed batteries. Obstruction between remote and TV. Remote control malfunction.	Replace batteries with new AA ALKALINE batteries, ensuring correct polarity. Remove any objects blocking the line of sight to the TV's infrared receiver. Ensure the remote is pointed directly at the TV.
Buttons are unresponsive or sticky.	Dirt or debris under buttons. Worn out internal contacts.	Clean the remote control as described in Section 6.2. If cleaning does not resolve the issue, the remote may need replacement.
Remote works intermittently.	Low battery power. Interference from other electronic devices.	Replace batteries. Move other electronic devices away from the TV and remote control.

8. Specifications

Model Number	290P187040
Brand	ECONTROLLY
Product Dimensions	3.94 x 1.57 x 0.59 inches
Item Weight	2.47 ounces
Batteries Required	2 AA batteries (Alkaline recommended)
Special Feature	Pre Programmed
Color	Black
Max Number of Supported Devices	1
Compatible Devices	Television

9. Support

For any questions or further assistance regarding your ECONTROLLY 290P187040 Replacement Remote Control, please contact the seller or manufacturer directly. Refer to your purchase documentation for contact information.