AQUASPHERE ASR 105 Robotic Pool Cleaner User Manual

1. Introduction

Product Overview

The AQUASPHERE ASR 105 is an advanced robotic pool cleaner designed to efficiently clean the floor, walls, and waterline of your pool. It features powerful suction and intelligent navigation for thorough cleaning, ensuring a pristine pool environment.

Key Features

• Efficient cleaning for pools up to 9 x 4 meters with flat bottoms or gentle slopes.
• Rigid filter with 3-liter capacity and 150 micron filtration for capturing fine debris.
• Comprehensive cleaning cycle (approximately 2.5 hours) covering the pool floor, walls, and waterline.
• Intelligent sensors (gyroscope and accelerometer) for optimal movement and coverage.
• Intuitive operation and easy filter cleaning without direct contact with dirt particles.

2. Safety Instructions

Please read and understand all safety instructions before operating the AQUASPHERE ASR 105 robotic pool cleaner. Failure to follow these instructions may result in injury or damage to the product.

• Electrical Safety: Always ensure the control unit is placed in a dry, shaded area, at least 3.5 meters (11.5 feet) from the pool edge and protected from direct water exposure. Only use the provided power supply and control box. Do not operate the cleaner if the power cable or control unit is damaged.
• Water Safety: Do not operate the cleaner when people or animals are in the pool. The cleaner is designed for underwater use only.
• Handling: Always disconnect the power supply before performing any maintenance, cleaning, or when removing the cleaner from the pool. Do not pull the cleaner out of the water by its floating cable; always use the handle.
• Children and Pets: Keep children and pets away from the cleaner during operation and when it is connected to power.
• Grounding: This device features Class II double insulation, meaning it does not require grounding. Do not attempt to modify the plug or power cord.
• Storage: Store the cleaner and control box in a dry, protected area when not in use.

3. Product Components

The AQUASPHERE ASR 105 robotic pool cleaner system includes the following main components:

• Robotic Cleaner Unit: The main body of the cleaner, equipped with brushes, suction inlet, and internal motor.
• Floating Power Cable: A 15-meter cable that connects the robotic unit to the control box, designed to float on the water surface.
• Control Box: The external power supply and control unit for the robotic cleaner.
• Filter Canister: An internal, rigid filter with 3-liter capacity and 150 micron filtration for collecting debris.

Figure 3.1: Main view of the AQUASPHERE ASR 105 Robotic Pool Cleaner, showcasing its compact design and robust tracks.

Figure 3.2: Front view of the cleaner, highlighting the active brushing mechanism and suction inlet.

Figure 3.3: Side view of the cleaner, showing the durable tracks designed for efficient movement across pool surfaces.

Figure 3.4: Rear view of the cleaner, illustrating its streamlined design for optimal maneuverability.

Figure 3.5: Top view of the cleaner with the lid open, revealing the accessible filter canister for easy maintenance.

4. Setup

4.1 Unpacking

Carefully remove all components from the packaging. Ensure all parts listed in Section 3 are present and undamaged.

4.2 Connecting the Cleaner

1. Connect the floating power cable from the robotic cleaner unit to the designated port on the control box. Ensure the connection is secure and fully inserted.
2. Place the control box in a dry, shaded area, at least 3.5 meters (11.5 feet) away from the pool edge. Ensure it is protected from direct sunlight and water splashes.
3. Plug the control box into a suitable electrical outlet (220-240 VAC, 50/60 Hz).

4.3 Placing the Cleaner in the Pool

1. Gently immerse the robotic cleaner into the pool. Hold it by the handle and allow it to sink to the bottom.
2. As the cleaner submerges, tilt it slightly to release any trapped air bubbles. This ensures proper suction and movement.
3. Ensure the floating cable is untangled and has enough slack to allow the cleaner to reach all areas of the pool without restriction.

5. Operating Instructions

5.1 Starting a Cleaning Cycle

Once the cleaner is fully submerged and connected to the power supply:

1. Press the START button on the control box.
2. The ASR 105 will begin its automatic cleaning cycle, systematically covering the pool floor, walls, and waterline.
3. The complete cleaning cycle duration is approximately 2.5 hours.

5.2 Ending a Cleaning Cycle

The cleaner will automatically stop at the end of its programmed cycle.

1. To remove the cleaner from the pool, gently pull the floating cable until the cleaner is within reach.
2. Lift the cleaner out of the water using its handle. Do not pull the cleaner out of the water by the cable, as this can cause damage.
3. Allow any excess water to drain from the cleaner before placing it on a suitable surface.

6. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your AQUASPHERE ASR 105.

6.1 Filter Cleaning

It is highly recommended to clean the filter after each cleaning cycle, especially if the pool is heavily soiled.

1. Ensure the cleaner is disconnected from the power supply.
2. Open the top lid of the robotic cleaner unit.
3. Remove the filter canister from its compartment.
4. Empty any collected debris from the filter. Rinse the filter thoroughly with a garden hose until all debris is removed. The design allows for easy cleaning without direct contact with dirt particles.
5. Reinsert the clean filter canister back into its compartment, ensuring it is properly seated.
6. Close the top lid securely.

6.2 Cable Care

After each use, untangle the floating cable to prevent kinks and damage. Store the cable neatly, avoiding tight coiling that could stress the wires.

6.3 Storage

When the cleaner is not in use for extended periods (e.g., off-season), store the robotic unit and control box in a dry, shaded area, protected from extreme temperatures and direct sunlight. Ensure the cleaner is clean and dry before storage.

7. Troubleshooting

This section provides solutions to common issues you might encounter with your AQUASPHERE ASR 105.

8. Specifications

• Model: ASR 105
• Pool Size Compatibility: Up to 9 x 4 meters (30 x 13 feet)
• Cleaning Coverage: Pool Floor, Walls, and Waterline
• Cleaning Cycle Duration: Approximately 2.5 hours
• Suction Width: 230 mm
• Robot Supply Voltage: 30 VDC
• Control Unit Supply Voltage: 220-240 VAC, 50/60 Hz
• Maximum Power Consumption: 150 W
• Filter Type: Rigid, Single Filtration
• Filter Fineness: 150 microns (5)
• Filter Capacity: 3 Liters
• Cable Length: 15 meters (49 feet)
• Robot Dimensions (L x W x H): 41 x 42 x 28 cm (16.1 x 16.5 x 11 inches)
• Robot Weight (without cable): 8 kg (17.6 lbs)
• Insulation Class: Class II (Double/Reinforced Insulation, no grounding required)
• Compatibility: Compatible with all pool linings

9. Warranty and Support

9.1 Warranty Information

This AQUASPHERE ASR 105 robotic pool cleaner comes with a 2-year warranty from the date of purchase. Please retain your original proof of purchase (receipt or invoice) as it will be required for any warranty claims. The warranty covers manufacturing defects and malfunctions under normal use conditions.

9.2 Customer Support

For technical assistance, troubleshooting, spare parts, or warranty inquiries, please contact AQUASPHERE customer support. You can typically find contact details (phone number, email, or support portal) on the official AQUASPHERE website or through your local distributor.

When contacting support, please have your product model (ASR 105) and serial number (if applicable) ready, along with a detailed description of the issue.