Andis 73130

Download PDF
Contents

Andis 73130 Envy Li Cordless Clipper User Manual

Model: 73130

Introduction

This manual provides detailed instructions for the safe and effective use of your Andis 73130 Envy Li Cordless Clipper. Please read all instructions carefully before operating the device and retain this manual for future reference.

Andis 73130 Envy Li Cordless Clipper, front view

Figure 1: Andis 73130 Envy Li Cordless Clipper. This image shows the main view of the clipper, highlighting its ergonomic design and blade.

Product Overview

The Andis 73130 Envy Li Cordless Clipper is a professional-grade hair clipper designed for precision cutting and comfortable use. It features a powerful rotary motor, an adjustable carbon-steel blade, and a long-lasting lithium-ion battery for cordless operation.

  • Cordless Operation: Provides freedom of movement without power cord restrictions.
  • Adjustable Blade: Carbon-steel blade adjusts from size 000 to 1, suitable for various cutting lengths and zero-gapping.
  • Powerful Rotary Motor: Delivers 5,500 strokes per minute (SPM) for efficient cutting with minimal noise.
  • Ergonomic Design: Lightweight and designed for comfortable handling during extended use.
  • Lithium-Ion Battery: Offers up to two hours of continuous power on a full charge.

Setup and Initial Use

Unpacking and Inspection

Carefully remove all components from the packaging. Inspect the clipper and accessories for any signs of damage. Ensure all listed items are present:

  • Andis 73130 Envy Li Cordless Clipper
  • Blade Guard
  • Blade Oil
  • Charging Adapter
  • 11 Attachment Combs

Charging the Clipper

Before first use, fully charge the clipper. Connect the charging adapter to the clipper's charging port and plug it into a suitable electrical outlet. The clipper uses a 100-240V / 50-60 Hz voltage adapter. Ensure your local voltage is compatible. A full charge provides approximately two hours of cordless operation.

Andis 73130 Envy Li Cordless Clipper charging port

Figure 2: Charging port location on the Andis Envy Li Clipper. This image shows a close-up of the charging port at the base of the clipper.

Blade Adjustment and Zero-Gapping

The clipper's carbon-steel blade can be adjusted from size 000 (closest cut) to size 1. For razor-sharp lines and extremely close cutting, the blade can be "zero-gapped." This adjustment should be performed with care to avoid skin irritation. Refer to the detailed instructions below for zero-gapping:

  1. Ensure the clipper is turned off and unplugged.
  2. Loosen the two screws on the blade set slightly.
  3. Carefully align the small moving blade with the large stationary blade, ensuring the cutting edge of the small blade is just below the top edge of the large blade.
  4. Tighten the screws securely.
  5. Test the blade on a small section of hair or skin to ensure proper adjustment and comfort.
Andis 73130 Envy Li Cordless Clipper blade close-up

Figure 3: Close-up view of the adjustable blade on the Andis Envy Li Clipper. This image details the blade set, showing the two screws for adjustment.

Operating Instructions

Turning On/Off

To turn the clipper on, slide the thumb-controlled power switch to the "ON" position. To turn it off, slide the switch to the "OFF" position.

Using Attachment Combs

The clipper includes 11 attachment combs for various cutting lengths. To attach a comb, align it with the clipper blade and snap it securely into place. To remove, gently pull the comb away from the blade.

General Cutting Tips

  • Always start with clean, dry hair.
  • Use the appropriate attachment comb for the desired length.
  • Hold the clipper firmly and move it against the direction of hair growth for an even cut.
  • Overlap strokes to ensure no hair is missed.
  • Regularly clear hair from the blade during use to maintain optimal performance.

Maintenance and Care

Cleaning the Blades

After each use, turn off and unplug the clipper. Use a small brush (not included, but recommended) to remove loose hair from the blades. For thorough cleaning, the blade set can be removed (refer to blade adjustment section for screw locations) and cleaned with a blade cleaner solution (sold separately) or warm soapy water. Ensure blades are completely dry before reattaching.

Oiling the Blades

To ensure smooth operation and prolong blade life, oil the blades before and after each use. Apply a few drops of the included blade oil across the teeth of the blade. Turn the clipper on for a few seconds to allow the oil to distribute evenly. Wipe off any excess oil with a clean cloth.

Diagram showing how to oil clipper blades

Figure 4: Blade oiling diagram. This illustration demonstrates the correct method for applying oil to the clipper blades.

Storage

Store the clipper in a cool, dry place, away from moisture and direct sunlight. Keep the blade guard on the clipper when not in use to protect the blades.

Troubleshooting Guide

ProblemPossible CauseSolution
Clipper does not turn on.Battery is depleted.Charge the clipper fully.
Clipper runs slowly or pulls hair.Blades are dull, dirty, or not oiled.Clean and oil the blades. If problem persists, blades may need sharpening or replacement.
Excessive noise or vibration.Blades are loose or motor issue.Ensure blade screws are tightened. If noise persists after proper oiling, contact customer support.
Clipper gets hot during use.Extended use or lack of lubrication.Allow clipper to cool down. Ensure blades are properly oiled.
Clipper not charging.Faulty adapter or power outlet.Check power outlet. Ensure charging adapter is securely connected and undamaged. Verify voltage compatibility (100-240V / 50-60 Hz).

Product Specifications

  • Model Number: 73130
  • Brand: Andis
  • Power Source: Battery Powered (Lithium-Ion)
  • Motor Type: Rotary
  • Strokes Per Minute (SPM): 5,500
  • Blade Type: Adjustable Carbon-Steel Blade (sizes 000 to 1)
  • Input Voltage: 100-240V / 50-60 Hz (Charging Adapter)
  • Item Weight: Approximately 9.9 ounces (0.28 kg)
  • Package Dimensions: 9.88 x 7.95 x 2.64 inches (25.1 x 20.2 x 6.7 cm)
  • Included Accessories: Blade Guard, Blade Oil, Charging Plugs, 11 Attachment Combs
  • UPC: 040102731303

Warranty Information

Andis products are manufactured to high standards and are inspected before shipment. While specific warranty details are not provided in this manual, typically Andis offers a limited warranty against defects in material or workmanship for a specified period from the date of purchase. Please retain your proof of purchase. For detailed warranty terms and conditions, please refer to the warranty card included with your product or visit the official Andis website.

Customer Support

If you have any questions, require assistance, or encounter issues not covered in this manual, please contact Andis customer support. You can find contact information on the official Andis website or through the retailer where you purchased the product.

Online Resources: For additional tips, tutorials, and product information, visit the official Andis website: www.andis.com

Instructional Videos

No specific instructional video URLs were provided in the product data. For visual guides on clipper usage, maintenance, and styling techniques, please visit the official Andis website or their authorized YouTube channel.

© 2024 Andis Company. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.