TECKNET Wireless Doorbell with Dual Receivers - Model B0CHVWL5L6 User Manual

1. Introduction

Thank you for choosing the TECKNET Wireless Doorbell. This manual provides detailed instructions for the installation, operation, and maintenance of your new doorbell system. This system features an IP66 waterproof outdoor transmitter and two portable battery-powered receivers, offering a wireless range of up to 400 meters, 60 selectable melodies, 5 adjustable volume levels, and RGB flashing lights for enhanced visibility.

Image 1.1: TECKNET Wireless Doorbell receiver in various home settings.

Image 1.2: The doorbell system is suitable for various environments such as homes, offices, warehouses, and gardens.

2. Package Contents

Please check the package contents to ensure all items are present:

• 1 x Wireless Doorbell Transmitter (Button)
• 2 x Wireless Doorbell Receivers
• 1 x CR2032 Battery (pre-installed in transmitter)
• Mounting Hardware (Screws, Wall Plugs, Adhesive Tape)
• 1 x User Manual (this document)

Note: 3x AA batteries for each receiver are NOT included and must be purchased separately.

3. Setup and Installation

3.1. Transmitter (Doorbell Button) Installation

1. Prepare the Transmitter: The CR2032 battery is typically pre-installed. If not, gently open the transmitter casing and insert the CR2032 battery with the positive (+) side facing up.
2. Choose a Mounting Location: Select a flat, clean surface near your door. Ensure the surface is free from dust and moisture.
3. Mounting Options:
   • Adhesive Tape: Peel off one side of the double-sided adhesive tape and stick it to the back of the transmitter. Peel off the other side and firmly press the transmitter onto the desired surface for at least 30 seconds.
   • Screws: Open the transmitter casing. Mark the positions for drilling holes using the back plate as a template. Drill two holes, insert the wall plugs, and then secure the back plate with screws. Attach the transmitter to the secured back plate.

Image 3.1: Installation methods for the doorbell transmitter (button).

3.2. Receiver Installation

1. Insert Batteries: Open the battery compartment on the back of each receiver. Insert 3x AA batteries into each receiver, ensuring correct polarity (+/-).
2. Placement: Place the receivers in desired locations within your home or office. The wireless range is up to 400 meters in open areas, but may be reduced by walls and obstacles.

Image 3.2: Illustration of the doorbell system with dual receivers and 400m range.

3.3. Pairing (If Necessary)

The transmitter and receivers are typically pre-paired at the factory. If they do not ring when the button is pressed, follow these steps to pair them:

• Press and hold the volume button on the receiver for approximately 5 seconds until it emits a short chime and the RGB light flashes. This indicates it is in pairing mode.
• Immediately press the doorbell transmitter button. The receiver will chime again, confirming successful pairing.
• Repeat for the second receiver if applicable.

4. Operating Instructions

4.1. Adjusting Volume

The receiver offers 5 levels of adjustable volume, from 0 dB (silent) to 110 dB. Press the Volume button on the side of the receiver repeatedly to cycle through the volume levels until your desired setting is reached.

Image 4.1: Different volume levels for various scenarios.

4.2. Changing Melodies

There are 60 classic melodies to choose from. Press the Song Selection button (usually indicated by a music note icon) on the side of the receiver to cycle through the available melodies. The receiver will play each melody as you press the button.

4.3. RGB Flashing Lights and Silent Mode

When the doorbell receives a signal, the RGB lights on the receiver will flash. This feature can be deactivated if preferred. To select the mode (sound + light, light only, or sound only), press and hold the Song Selection button for three seconds. In silent mode (light only), the RGB lights will flash, providing a visual alert, which is particularly useful for the hearing impaired.

Image 4.2: Receiver features including RGB lights, melodies, and volume control.

4.4. Memory Function

The doorbell kit features a memory function that retains your last selected melody and volume level, even after a power outage or battery replacement. You do not need to reset these settings.

5. Maintenance

5.1. Battery Replacement

• Transmitter (Button): The transmitter uses one CR2032 battery, which typically lasts up to 54 months. To replace, gently open the casing, remove the old battery, and insert a new CR2032 battery with the positive (+) side facing up.
• Receivers: Each receiver requires three AA batteries, which typically last up to 36 months. When the receiver's battery is low, a red indicator light will illuminate. To replace, open the battery compartment on the back, remove the old batteries, and insert new AA batteries, ensuring correct polarity.

Image 5.1: Battery life and low battery reminder feature.

5.2. Cleaning

Wipe the doorbell transmitter and receivers with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the surface or internal components.

5.3. Waterproof Rating

The outdoor transmitter is rated IP66 waterproof, meaning it is protected against powerful water jets and dust. It is designed to withstand extreme weather conditions, including rain and snow, and operates within a temperature range of -20°C to 60°C (-4°F to 140°F).

Image 5.2: IP66 waterproof rating and temperature resistance of the transmitter.

6. Troubleshooting

• Doorbell not ringing:
  • Check if the receiver batteries are correctly installed and not depleted. Replace if necessary.
  • Ensure the transmitter battery is functional.
  • Verify that the receiver is not in silent (0 dB) mode.
  • Re-pair the transmitter and receiver(s) as described in Section 3.3.
• Short wireless range:
  • Thick walls, metal structures, or other electronic devices can interfere with the signal. Try relocating the receivers or transmitter.
  • Ensure there are no large metal objects directly between the transmitter and receiver.
• Intermittent ringing:
  • This could indicate low battery in either the transmitter or receiver. Replace batteries.
  • Check for potential signal interference from other wireless devices.

7. Specifications

8. Warranty and Support

TECKNET offers a 36-month warranty for this product, reserved for registered users. Please register your product on the official TECKNET website to activate your warranty.

Spare parts availability in the EU is guaranteed for 3 years.

For technical support, troubleshooting assistance, or warranty claims, please visit the official TECKNET website or contact their customer service directly. Contact information can typically be found on the product packaging or the brand's website.