1. Product Overview
The FLIPSKY Anti Spark Switch V1.0 200A is designed to efficiently and safely protect power contacts from electrical sparks. This device prevents the burning and oxidation of power contacts, safeguards integrated circuit components from breakdown and damage, and mitigates the risk of explosions caused by electric sparks. It effectively extends the lifespan of electronic products in high-power applications.
Featuring an aluminum substrate PCB, this anti-spark switch offers superior heat dissipation performance, allowing for the addition of larger heat sinks for continuous high current output. The heat sink and the PCB are connected with thermally conductive silicone grease for optimal heat transfer.
2. Key Features
- MOSFETs: Utilizes 10x10 large package MOS fets for enhanced overcurrent capacity and heat dissipation.
- Voltage Rating: Supports a maximum voltage of 20S (90V), safe for operation up to 80V.
- Current Capacity: Provides a continuous current of 80A and a maximum current of 200A (with an increased heat sink). Theoretical burst current is 1000A.
- Control Mode: Features a lock key control switch mode. Pressing the lock button activates the switch and illuminates the LED; pressing it again deactivates the switch and turns off the LED.
- Dimensions: Compact size of 68mm x 34mm x 9.5mm (with 12AWG wire).
- LED Button: Standard 12mm diameter LED button.
- Aluminum PCB: Enhanced heat dissipation due to the aluminum substrate.
3. Specifications
| Specification | Value |
|---|---|
| Hardware Version | V1.0 |
| Max Voltage | 20S (90V, safe for 80V) |
| Continuous Current | 80A |
| Max Current | 200A (with increased heat sink) |
| Burst Current (Theoretical) | 1000A |
| Dimensions (L x W x H) | 68mm x 34mm x 9.5mm |
| LED Button Diameter | 12mm |
| Wire Gauge | 12AWG (Note: Some units may have 10AWG) |
| Material | Aluminum PCB/Case |
| Switch Type | MOSFET |
| Control Method | Lock Key Control Switch Mode |
| Compatible Devices | Electric Skateboard, Ebike, Scooter, Robots |
4. Setup and Installation
Proper installation is crucial for the safe and effective operation of the Anti Spark Switch. Refer to the wiring diagram and follow these steps:
- Identify Connections: The switch has clearly labeled 'IN' and 'OUT' terminals for power, and a 'K+ L Lk-' port for the LED button.
- Battery Connection: Connect the 'IN' terminals of the anti-spark switch to your battery's positive (+) and negative (-) terminals. Ensure correct polarity (red wire to positive, black wire to negative).
- Load Connection: Connect the 'OUT' terminals of the anti-spark switch to your electronic speed controller (ESC) or other load. Again, observe correct polarity.
- LED Button Connection: Connect the provided LED button to the 'K+ L Lk-' port. The LED button typically has three wires: K+ (LED positive), L (switch signal), and Lk- (LED negative/ground). Refer to the specific wiring of your LED button for correct connection to these pins.
- Heat Management: For applications requiring continuous high current output (approaching 200A), it is recommended to add a larger external heat sink to the aluminum PCB for optimal thermal performance. Ensure good contact between the heat sink and the switch using thermally conductive silicone grease.
- Secure Mounting: Mount the anti-spark switch securely in a location that is protected from physical damage and moisture, and allows for adequate airflow if an external heat sink is not used.

Figure 1: Wiring diagram illustrating the connection of the FLIPSKY Anti Spark Switch V1.0 200A between a battery, VESC, and motors.
5. Operating Instructions
The FLIPSKY Anti Spark Switch V1.0 200A operates using a simple lock key control switch mode:
- To Turn On: Press the connected lock button. The button will latch into the 'on' position, and the integrated LED light will illuminate, indicating that power is flowing through the switch.
- To Turn Off: Press the lock button again. The button will release from the latched position, and the LED light will turn off, indicating that the power circuit has been safely disconnected.
Always ensure the switch is in the 'off' position before connecting or disconnecting the battery or performing any maintenance on your system.
6. Maintenance
The FLIPSKY Anti Spark Switch V1.0 200A is designed for durability and reliability. Minimal maintenance is required, but regular checks can ensure optimal performance and longevity:
- Visual Inspection: Periodically inspect the switch and its wiring for any signs of damage, wear, or loose connections. Check for discoloration on the PCB or wires, which could indicate overheating.
- Cleanliness: Keep the switch free from dust, dirt, and moisture. Use a soft, dry brush or compressed air to clean the unit if necessary. Avoid using liquid cleaners.
- Connection Integrity: Ensure all power and control wire connections remain secure. Loose connections can lead to increased resistance, heat, and potential failure.
- Thermal Management: If operating under high load, regularly check that the heat sink (if installed) is clean and making good contact with the switch.
7. Troubleshooting
If you encounter issues with your FLIPSKY Anti Spark Switch, consider the following troubleshooting steps:
- Switch Not Turning On:
- Check battery voltage: Ensure the battery is charged and within the specified voltage range (up to 80V safe operating voltage).
- Verify LED button connection: Ensure the LED button is correctly wired to the 'K+ L Lk-' port and is functioning.
- Inspect power connections: Confirm that the 'IN' wires from the battery and 'OUT' wires to the load are securely connected with correct polarity.
- Switch Not Turning Off:
- Check LED button functionality: Ensure the lock button mechanism is not stuck and can be pressed to release.
- Inspect control wiring: Verify the integrity of the wires connecting the LED button to the switch.
- Excessive Heat:
- Check current draw: Ensure the continuous current draw does not exceed 80A without an additional heat sink, or 200A with an adequate heat sink.
- Verify connections: Loose or poor connections can generate heat.
- Ensure proper airflow: If no external heat sink is used, ensure the switch is in a location with sufficient airflow.
- Consider adding a larger heat sink: For high-power applications, an external heat sink is highly recommended.
- No Power Output:
- Confirm switch is 'on': Ensure the LED button is latched and illuminated.
- Check all wiring: Re-verify all power connections from battery to switch and switch to load for continuity and correct polarity.
- Inspect for internal damage: If all external checks pass, there might be an internal component failure.
If problems persist after performing these checks, contact FLIPSKY customer support for further assistance.
8. Safety Information
Adhere to the following safety guidelines when installing and operating the FLIPSKY Anti Spark Switch V1.0 200A:
- Electrical Safety: Always disconnect the battery before making or changing any electrical connections. High voltage and current can be dangerous.
- Polarity: Ensure all connections are made with correct polarity (positive to positive, negative to negative). Incorrect polarity can cause severe damage to the switch and connected components.
- Insulation: Properly insulate all exposed wires and connections to prevent short circuits.
- Overcurrent Protection: While the anti-spark switch provides protection against initial spark, ensure your system has appropriate overcurrent protection (e.g., fuses or circuit breakers) for the overall circuit.
- Heat Management: Operating the switch beyond its continuous current rating without adequate heat dissipation can lead to overheating and damage. Consider an external heat sink for high-power applications.
- Environmental Conditions: Do not expose the switch to water, excessive humidity, or extreme temperatures.
- Professional Installation: If you are unsure about any aspect of the installation, seek assistance from a qualified professional.
9. What's in the Box
The package for the FLIPSKY Anti Spark Switch V1.0 200A typically includes:
- 1x FLIPSKY Anti Spark Switch Aluminum PCB
- 1x LED Button (usually pre-wired or with connector)
10. Product Media
Product Images
Product Videos
Official product video demonstrating the FLIPSKY Anti Spark Switch V1.0 200A in various applications and providing an overview of its features.




