Introduction
Welcome to the user manual for your Edifier X2 True Wireless Bluetooth Headphones Earbuds. This guide provides detailed instructions on how to set up, operate, maintain, and troubleshoot your device to ensure optimal performance and a satisfying audio experience. Please read this manual thoroughly before using your earbuds.
Image: Edifier X2 earbuds and their charging case.
Setup
What's in the Box
- Edifier X2 True Wireless Earbuds
- Charging Case
- Charging Cable
- User Manual
Charging the Earbuds and Case
Before first use, fully charge the earbuds and the charging case. Place the earbuds into the charging case. Connect the charging case to a power source using the provided USB cable. The indicator light on the case will show charging status. A full charge for the case typically takes approximately 2 hours. The earbuds provide up to 7 hours of playback on a single charge, with the charging case extending total playtime to 28 hours.
Image: Visual representation of charging times and total playback duration.
Pairing with a Device
- Open the charging case and remove both earbuds. The earbuds will automatically enter pairing mode, indicated by rapidly blinking red and blue LEDs.
- On your Bluetooth-enabled device (smartphone, tablet, computer), go to the Bluetooth settings.
- Search for available devices and select "EDIFIER X2" from the list to connect.
- Once connected, the earbud LEDs will turn off, and you will hear an audible confirmation.
For subsequent use, the earbuds will automatically reconnect to the last paired device when removed from the case, provided Bluetooth is enabled on the device.
Image: Example of pairing the Edifier X2 earbuds with a mobile device.
Operating Instructions
Wearing the Earbuds
Gently insert the earbuds into your ears, ensuring a comfortable and secure fit. The ergonomic design is intended for long-lasting comfort and stability during various activities.
Touch Controls
The Edifier X2 earbuds feature intuitive touch controls on each earbud. Refer to the table below for common functions:
| Action | Control |
|---|---|
| Pause/Play Music | Double-click the left or right earbud |
| Accept/End a Call | Double-click the left or right earbud |
| Next Track | Triple-click the right earbud |
| Game Mode On/Off | Triple-click the left earbud |
| Reject a Call | Press and hold the left or right earbud for 3 seconds |
| Activate Voice Assistant | Triple-click the left or right earbud |
Image: Detailed diagram of touch control gestures and their corresponding functions.
Call Functions
The Edifier X2 earbuds are equipped with dual microphones and advanced call noise reduction technology to ensure clear voice quality during calls, even in noisy environments. Use the touch controls to manage your calls.
Image: Illustrates the clear call quality provided by the earbuds' noise reduction feature.
Sound Quality
Experience rich HiFi stereo sound delivered by the impressive 13mm large dynamic drivers. These drivers ensure a wide soundstage and balanced audio, allowing for an immersive listening experience.
Image: Cutaway diagram highlighting the 13mm large dynamic driver and Bluetooth 5.1 chip.
Maintenance
Cleaning
To maintain optimal performance and hygiene, regularly clean your earbuds and charging case. Use a soft, dry, lint-free cloth to wipe down the surfaces. Avoid using abrasive materials or harsh chemicals. For the earbud grilles, gently remove any debris with a small, soft brush.
Water Resistance
The Edifier X2 earbuds feature an IPX54 water-resistant rating. This means they are protected against dust ingress and splashing water from any direction. They are suitable for use during workouts, running, or in light rain. However, they are not designed for submersion in water or exposure to pressurized water jets. Ensure the earbuds are dry before placing them back in the charging case.
Image: Earbuds shown with water droplets, emphasizing their IPX54 water-resistant capabilities.
Troubleshooting
- Earbuds not pairing: Ensure both earbuds are out of the case and fully charged. Turn off and on your device's Bluetooth. If issues persist, try resetting the earbuds (refer to manufacturer's website for specific reset instructions if not in manual).
- No sound from one earbud: Place both earbuds back into the charging case, close the lid, wait a few seconds, then take them out again. Check your device's audio balance settings.
- Charging issues: Verify the charging cable is securely connected to both the case and the power source. Ensure the charging contacts on the earbuds and inside the case are clean and free of debris.
- Poor call quality: Ensure the microphones are not obstructed. Move closer to your connected device to improve signal strength.
- Intermittent connection: Reduce the distance between the earbuds and your device. Avoid environments with significant wireless interference.
Specifications
| Feature | Detail |
|---|---|
| Model Name | Edifier X2 |
| Connectivity Technology | Wireless (Bluetooth) |
| Bluetooth Version | 5.1 |
| Bluetooth Range | 10 Meters |
| Audio Driver Type | Dynamic Driver |
| Audio Driver Size | 13 Millimeters |
| Frequency Range | 20Hz - 20KHz |
| Impedance | 32 Ohm |
| Battery Life (Earbuds) | Up to 7 Hours |
| Total Playtime (with Case) | Up to 28 Hours |
| Charging Time | Approx. 2 Hours (Case) |
| Water Resistance Level | IPX54 |
| Control Type | Touch-based Controller |
| Item Weight | 1.76 ounces (50 Grams) |
| Compatible Devices | Android, Cell Phone, Computer, Laptop |
Warranty and Support
Edifier products are designed and manufactured to the highest quality standards. For information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or visit the official Edifier website. For technical support, frequently asked questions, or further assistance, please visit the Edifier support page or contact their customer service directly.
Official Edifier Website: www.edifier.com
