LILYGO T-SIM7600G-H

Download PDF
Contents

LILYGO T-SIM7600G-H Development Board User Manual

Model: T-SIM7600G-H

1. Introduction

The LILYGO T-SIM7600G-H is a versatile development board integrating an ESP32-WROVER microcontroller with a SIM7600G wireless communication module. This board offers comprehensive connectivity options including Wi-Fi, Bluetooth, 4G LTE CAT4, and GPS. Designed for various application scenarios, it features an integrated 18650 battery holder and a solar charging interface for enhanced portability and power management.

LILYGO T-SIM7600G-H Development Board Front View

Figure 1.1: Front view of the LILYGO T-SIM7600G-H Development Board.

2. Product Overview

2.1 Key Features

  • Integrated Wireless Module: Features SIM7600G for 4G LTE CAT4, GPS, with Wi-Fi and Bluetooth via ESP32-WROVER.
  • Power Management: Built-in 18650 battery holder and solar charging interface.
  • Dual USB-C Interfaces: Two T-type-c interfaces for flexible connectivity and power.
  • Low Power Consumption: GPS power control allows for ultra-low power consumption, reaching approximately 300uA in sleep mode.
  • Development Friendly: Based on ESP32, offering a robust platform for various IoT and communication projects.

2.2 Component Identification

LILYGO T-SIM7600G-H Labeled Diagram

Figure 2.1: Labeled diagram of the T-SIM7600G-H board's front components.

Refer to Figure 2.1 for the location of key components:

  • ESP32 Programming Download Port: USB-C port for programming the ESP32.
  • USB Interface: Additional USB-C port for general use or power.
  • Reset Button: Resets the board.
  • SIM Module Power Button: Controls power to the SIM7600G module.
  • Nano SIM Slot: For inserting a Nano SIM card for cellular connectivity.
  • Solar Charging Cable Interface: Connector for solar panel input.
  • Power Switch: Main power control for the board.
  • TF Card Slot: For inserting a MicroSD (TF) card.
LILYGO T-SIM7600G-H Back View with Battery Holder

Figure 2.2: Back view of the T-SIM7600G-H board, showing the 18650 battery holder.

Figure 2.2 illustrates the back of the board, prominently featuring the 18650 battery holder. Ensure correct polarity when inserting the battery.

3. Setup

Follow these steps to set up your LILYGO T-SIM7600G-H board:

  1. Insert 18650 Battery: Carefully insert a 3.7V 18650 Li-ion battery into the battery holder on the back of the board, observing the correct polarity (+/-).
  2. Insert Nano SIM Card: Locate the Nano SIM slot and gently insert your activated Nano SIM card. Ensure it clicks into place.
  3. Connect Antennas:
    • Connect the provided GPS antenna to the designated U.FL connector (often labeled 'GPS').
    • Connect the provided LTE antenna to its respective U.FL connector (often labeled 'SIM' or 'LTE').
    LILYGO T-SIM7600G-H Antenna Connections

    Figure 3.1: Proper connection of GPS and SIM (LTE) antennas.

  4. Connect to Computer (Optional): For programming or initial power, connect the board to your computer using a USB-C cable via the ESP32 programming download port.
  5. Connect Solar Panel (Optional): If using solar charging, connect a compatible solar panel (4-6V input) to the solar charging cable interface. Ensure the solar panel is placed in direct sunlight for optimal charging.
    LILYGO T-SIM7600G-H Solar Charging Setup

    Figure 3.2: Example setup for solar charging the T-SIM7600G-H board.

4. Operating Instructions

4.1 Powering On/Off

  • To power on the board, slide the Power Switch to the ON position.
  • To power off, slide the Power Switch to the OFF position.
  • The SIM Module Power Button can be used to independently control the power to the SIM7600G module, allowing for power saving when cellular connectivity is not required.

4.2 Programming and Development

The LILYGO T-SIM7600G-H board is compatible with the Arduino IDE and ESP-IDF development frameworks. For detailed programming guides, example code, and firmware updates, please refer to the official LILYGO GitHub repository:

github.com/Xinyuan-LilyGO/T-SIM7600X

Ensure you have the necessary ESP32 board definitions and drivers installed in your development environment before attempting to upload code.

5. Maintenance

  • Handling: Handle the board with care to avoid damaging components or connections. Avoid static discharge.
  • Environment: Keep the board in a dry environment, away from moisture, extreme temperatures, and direct sunlight when not in use.
  • Cleaning: If necessary, gently clean the board with a soft, dry brush or compressed air. Do not use liquids or abrasive cleaners.
  • Battery Care: If using the 18650 battery, ensure it is charged regularly and stored properly. Avoid over-discharging or over-charging the battery.

6. Troubleshooting

  • Board does not power on:
    • Check if the 18650 battery is inserted correctly and fully charged.
    • Ensure the Power Switch is in the ON position.
    • If powered via USB, ensure the USB cable is properly connected and the power source is active.
  • No cellular network connection:
    • Verify that the Nano SIM card is correctly inserted and activated with a cellular plan.
    • Ensure the LTE antenna is securely connected.
    • Check if the SIM Module Power Button is enabled.
    • Confirm network coverage in your area.
  • GPS not acquiring signal:
    • Ensure the GPS antenna is securely connected.
    • Operate the board outdoors or near a window with a clear view of the sky.
    • Verify that GPS power control is not disabling the module in your software.
  • Programming errors:
    • Install the correct USB drivers for the board.
    • Select the correct board and COM port in your IDE.
    • Refer to the LILYGO GitHub repository for specific programming instructions and common issues.

7. Specifications

FeatureDetail
Model NameT-SIM7600G-H
BrandLILYGO
ProcessorESP32-WROVER (ARM Processor)
Cellular ModuleSIM7600G (4G LTE CAT4)
Connectivity TechnologyWi-Fi, Bluetooth, 4G LTE, GPS
Memory Storage Capacity4 MB
Battery HolderIntegrated 18650 Battery Holder
Charging InterfaceUSB-C, Solar Charging (4-6V input)
SIM Card TypeNano SIM
Operating System CompatibilityMac OS (and other common development environments)

8. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your point of purchase. For technical support, detailed documentation, and community forums, please visit the official LILYGO GitHub repository and community channels. LILYGO continuously updates its resources to assist developers and users.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.