1. Introduction
The Fanvil DS102 Desktop Stand is an essential accessory designed to facilitate the desktop installation of the Fanvil i56A Indoor Doorphone and Intercom Station. This bracket accessory package provides a stable and space-saving solution, allowing the i56A unit to be conveniently placed on a desk or flat surface rather than being wall-mounted. Its robust metal construction ensures durability and reliable support for your intercom station.
2. Safety Information
- Ensure the stand is placed on a stable, flat, and level surface to prevent the connected device from tipping over.
- Do not expose the stand to excessive moisture, direct sunlight, or extreme temperatures.
- Keep the stand away from heat sources and open flames.
- Avoid dropping or subjecting the stand to strong impacts, as this may cause damage.
- Do not attempt to modify or disassemble the stand. Any unauthorized modifications may void the warranty and pose safety risks.
- Keep out of reach of children and pets.
3. What's in the Box
Upon opening the package, verify that all components are present and undamaged:
- 1 x Fanvil DS102 Table Desk Stand
Note: The Fanvil i56A Indoor Doorphone and Intercom Station is sold separately and is not included with this stand.
4. Setup Instructions
The Fanvil DS102 Desktop Stand is designed for easy assembly and integration with your Fanvil i56A Indoor Station. Follow these steps for proper setup:
- Unpack the Stand: Carefully remove the DS102 Desktop Stand from its packaging. Inspect it for any signs of damage during transit.
- Prepare the i56A Unit: Ensure your Fanvil i56A Indoor Station is ready for desktop installation. Refer to the i56A's manual for any specific preparation steps.
- Attach the i56A to the Stand: Align the mounting points on the back of the Fanvil i56A Indoor Station with the corresponding slots or attachment points on the DS102 Desktop Stand. Gently slide or click the i56A into place until it is securely fastened. The design ensures a snug fit.
- Position the Stand: Place the assembled i56A and DS102 stand on your desired flat, stable desktop surface. Ensure there is adequate space around the unit for ventilation and cable management.
- Connect Cables: Once the i56A is securely on the stand, connect all necessary cables (e.g., power, network) to the i56A unit. Route cables neatly to maintain a tidy workspace.
Figure 4.1: Fanvil DS102 Desktop Stand. This image shows the front view of the grey metal stand, featuring two elongated oval cutouts for design and ventilation, and black anti-slip feet at the base.
5. Operating the Stand
The Fanvil DS102 is a passive accessory designed to provide a stable base for your Fanvil i56A Indoor Station. There are no active "operating" steps for the stand itself. Once the i56A is securely mounted on the DS102, the stand functions by holding the device in an upright, accessible position on a flat surface. Ensure the stand is always placed on a stable, level surface to prevent accidental tipping or damage to the connected device.
6. Maintenance
Regular maintenance of your Fanvil DS102 Desktop Stand will help preserve its appearance and functionality:
- Cleaning: Use a soft, dry, lint-free cloth to wipe down the stand. For stubborn marks, a slightly damp cloth with mild soap can be used, followed immediately by a dry cloth. Avoid abrasive cleaners, solvents, or strong chemicals, as these can damage the metal finish.
- Inspection: Periodically check the stand for any signs of wear, damage, or loose connections. Ensure the rubber feet are intact to maintain stability and prevent scratching surfaces.
- Storage: If storing the stand for an extended period, ensure it is clean and dry. Store it in a cool, dry place away from direct sunlight and extreme temperatures.
7. Troubleshooting
This section addresses common issues you might encounter with the Fanvil DS102 Desktop Stand:
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand is wobbly or unstable. | Uneven surface; i56A not properly seated; damaged stand. | Ensure the stand is on a flat, level surface. Re-seat the i56A unit firmly onto the stand. Inspect the stand for any physical damage. |
| i56A does not fit the stand. | Incorrect model of i56A; stand is damaged. | Verify that your indoor station is indeed a Fanvil i56A model. The DS102 is specifically designed for the i56A. If it is the correct model, check the stand for any deformities. |
| Scratches on desk surface. | Missing or damaged rubber feet. | Check if the black rubber feet on the bottom of the stand are present and intact. If missing or damaged, contact Fanvil support for replacement parts or use protective padding. |
8. Specifications
| Feature | Detail |
|---|---|
| Applicable Models | Fanvil i56A Indoor Station |
| Product Dimensions (L x W x H) | 170 x 110.94 x 13.5 mm (6.69 x 4.37 x 0.53 inches) |
| Material | Metal |
| Working Temperature | 0~45°C (32~113°F) |
| Item Weight | 178g (0.39 lbs / 6.28 oz) |
| Model Number | DS102 |
| UPC | 889837002209 |
9. Warranty and Support
Fanvil products are designed for reliability and performance. For specific warranty terms and conditions, please refer to the warranty card included with your Fanvil i56A Indoor Station or visit the official Fanvil website. The DS102 Desktop Stand is covered under the general accessory warranty policy.
For technical support, product inquiries, or assistance with troubleshooting, please contact Fanvil customer service or your authorized Fanvil dealer. You can typically find contact information on the official Fanvil website: www.fanvil.com