MAF 18-JD-MT10

Download PDF
Contents

MAF 18 Inch Full Size Bed Frame Instruction Manual

Model: 18-JD-MT10

1. Introduction

Thank you for choosing the MAF 18 Inch Full Size Bed Frame. This heavy-duty metal platform bed frame is designed for durability and stability, providing excellent support for your mattress without the need for a box spring. Its thoughtful design includes rounded corners for safety and ample under-bed storage space. Please read this manual carefully before assembly and use to ensure proper setup and long-lasting performance.

2. Important Safety Information

Please observe the following safety precautions to prevent injury or damage to the product:

  • Keep all parts and packaging materials out of reach of children.
  • Assemble the bed frame on a soft, non-abrasive surface (e.g., carpet or cardboard) to prevent scratches.
  • Ensure all bolts and screws are securely tightened before use. Periodically check and re-tighten connections.
  • Do not exceed the maximum weight capacity of 3000 LBS.
  • Avoid standing or jumping on the bed frame.
  • The rounded corners are designed to prevent injuries from toe bumps; however, exercise caution around the frame.
  • Use the provided anti-slip baffles to prevent the mattress from sliding.

3. Parts List

Before beginning assembly, verify that all components are present and undamaged. Refer to the diagram below for identification.

Exploded view of MAF bed frame parts with labels

Figure 3.1: Exploded view of bed frame components.

Table 3.1: Component List
PartDescriptionQuantity
ALegs (Corner)4
BSide Rails2
CHead/Foot End Rails2
DCenter Support Beams2
ECenter Support Legs2
FSlats12
GMattress Stopper2
HRubber Foot Pads4
IWrench1
JHex Key1
KBolts (various sizes)Assorted

4. Assembly Instructions

Follow these steps carefully for proper assembly. It is recommended to have two people for easier assembly, though it can be done by one person.

4.1 Unboxing and Preparation

Carefully open the packaging and lay out all components on a clean, soft surface to prevent damage. Identify each part using the Parts List (Section 3).

Video 4.1: Unboxing and initial setup of the bed frame components.

4.2 Frame Assembly

  1. Connect the side rails (B) to the corner legs (A) using the provided bolts. Ensure the U-shaped grooves on the rails are facing upwards.
  2. Attach the head and foot end rails (C) to the remaining corner legs (A).
  3. Connect the assembled side and end sections to form the main rectangular frame.
  4. Insert the center support beams (D) into the designated slots on the side rails.
  5. Attach the center support legs (E) to the center support beams (D). Ensure these legs are securely fastened.
  6. Place the slats (F) into the U-shaped grooves on the side rails and center support beams. Ensure they are evenly spaced and firmly seated.
  7. Install the mattress stoppers (G) on the head and foot ends of the frame by sliding them into the designated slots. Ensure they are mounted outwards to prevent mattress sliding.
  8. Attach the rubber foot pads (H) to the bottom of all legs to protect your floor and prevent slipping.
  9. Once all components are in place, use the provided hex key and wrench to fully tighten all bolts. Do not overtighten.
Assembled MAF 18 Inch Full Size Bed Frame

Figure 4.2: Fully assembled MAF bed frame.

Video 4.3: Detailed assembly steps for the bed frame.

5. Usage and Care

5.1 Mattress Placement

Place your mattress directly onto the steel slats. No box spring is needed for this platform bed frame. The anti-slip baffles and rubber foot cushions are designed to keep your mattress securely in place and prevent the frame from sliding.

Mattress placed on MAF bed frame

Figure 5.1: Mattress on the bed frame, showing no box spring needed.

5.2 Under-Bed Storage

This bed frame provides 16.4 inches of clearance for under-bed storage, allowing you to maximize space in your room. Utilize storage bins or containers to keep your belongings organized and the area tidy.

Under-bed storage space of MAF bed frame

Figure 5.2: Illustration of the generous under-bed storage space.

5.3 General Care

  • Wipe down the metal frame with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners.
  • Periodically check all bolts and connections to ensure they remain tight. Re-tighten if necessary to maintain stability and prevent squeaking.

6. Troubleshooting

6.1 Squeaking Noises

If your bed frame begins to squeak, it is most likely due to loose connections. Re-tighten all bolts on the frame, paying close attention to the main frame connections and the center support legs. Ensure the rubber foot pads are properly installed.

6.2 Mattress Sliding

The bed frame is equipped with plastic anti-skid baffles to prevent mattress movement. Ensure these baffles are correctly installed and facing outwards. If sliding persists, verify that your mattress is compatible with a platform bed and consider adding a non-slip mattress pad.

Mattress stopper detail on MAF bed frame

Figure 6.1: Proper installation of mattress stoppers.

7. Product Specifications

FeatureDetail
BrandMAF
Model Number18-JD-MT10
SizeFull
Product Dimensions74.5"L x 53.4"W x 18"H
Compatible Mattress Size75" x 54"
Weight Capacity3000 LBS (Static Pressure)
Under-Bed Storage Height16.4 inches
MaterialDurable Steel
Finish TypePowder Coated (Black)
Special FeaturesRounded Corners, Mattress Slide Stopper, Anti-slip Rubber Gaskets, Steel Slat Support, No Box Spring Needed, Easy Assembly
Item Weight31 pounds
Assembly RequiredYes
Dimensions of MAF Full Size Bed Frame

Figure 7.1: Detailed dimensions of the Full size bed frame.

8. Warranty and Support

For any questions, concerns, or assistance with your MAF bed frame, please contact MAF-SLEEP customer support. Refer to your purchase documentation for specific warranty details.

MAF-SLEEP is committed to producing high-quality products and providing excellent service.

Additional protection plans may be available through your retailer. Please check with your point of purchase for more information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.