Overstock 3-Light Vanity Light with Brushed Nickel Finish and Bath Set

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Overstock 3-Light Vanity Light and accompanying 5-Piece Bath Set. Please read this manual thoroughly before beginning installation and retain it for future reference.

Safety Information

WARNING: Risk of Electric Shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.

• All electrical connections must be in accordance with local codes and ordinances, National Electric Code (NEC), and ANSI/NFPA 70-1999.
• Consult a qualified electrician if you are unsure about the installation process.
• Do not connect this fixture to an ungrounded electrical system.
• Handle glass components with care to prevent breakage.
• Ensure all connections are secure and correct before restoring power.

Package Contents

Carefully unpack your product and ensure all items listed below are present and undamaged. If any parts are missing or damaged, do not attempt to assemble or install the product. Contact customer service for assistance.

• 3-Light Vanity Light Fixture (Brushed Nickel Finish)
• Clear Glass Shades (3)
• Towel Bar
• Towel Ring
• Toilet Paper Holder
• Robe Hook
• Mounting Hardware Kit
• Instruction Manual

Setup and Installation

Professional installation is recommended for electrical fixtures. If you are performing the installation yourself, ensure you follow all safety guidelines.

Tools Required (Not Included):

• Phillips Head Screwdriver
• Flat Head Screwdriver
• Wire Strippers
• Electrical Tape
• Pliers
• Safety Glasses
• Ladder (if necessary)

Vanity Light Installation Steps:

1. Turn Off Power: Locate the circuit breaker that supplies power to the light fixture outlet box. Turn off the power. Verify the power is off using a voltage tester.
2. Prepare Wiring: Carefully pull the electrical wires from the outlet box. Identify the hot (black), neutral (white), and ground (bare copper or green) wires.
3. Attach Mounting Plate: Secure the mounting plate to the outlet box using the provided screws. Ensure the plate is level.
4. Make Electrical Connections: Connect the fixture's black wire to the outlet box's black (hot) wire, the fixture's white wire to the outlet box's white (neutral) wire, and the fixture's ground wire to the outlet box's ground wire. Secure connections with wire nuts and wrap with electrical tape.
5. Mount Fixture: Carefully push the connected wires back into the outlet box. Align the fixture base with the mounting plate and secure it with the provided screws.
6. Install Glass Shades: Gently attach the clear glass shades to the fixture. Ensure they are securely fastened.
7. Install Bulbs: Insert incandescent bulbs (not included) of up to 60-Watt into each socket. Do not exceed the maximum wattage.
8. Restore Power: Turn the power back on at the circuit breaker. Test the light fixture.

Bath Set Installation Steps:

The bath set components (towel bar, towel ring, toilet paper holder, robe hook) typically install using wall anchors and screws. Specific instructions may vary slightly by component, but the general process is as follows:

1. Choose Location: Select appropriate locations on your wall for each accessory. Use a level to ensure proper alignment.
2. Mark Drilling Points: Hold the mounting bracket of each accessory against the wall and mark the screw hole locations with a pencil.
3. Drill Pilot Holes: Drill pilot holes at the marked points. Use a drill bit appropriate for your wall type (e.g., drywall, tile). Insert wall anchors if necessary.
4. Attach Mounting Brackets: Secure the mounting brackets to the wall using the provided screws.
5. Attach Accessories: Slide or screw the main accessory body onto its mounting bracket, securing it with set screws if applicable.

Operating Instructions

The 3-Light Vanity Light is designed for use with standard incandescent bulbs up to 60-Watt. It is compatible with a dimmer switch (not included) to allow for adjustable light intensity and to create a desired ambiance. Ensure the dimmer switch is rated for incandescent loads.

The bath set components are fixed accessories designed for holding towels, toilet paper, and robes. No specific operational instructions are required beyond their intended use.

Maintenance

Cleaning:

• Always disconnect power before cleaning the light fixture.
• Wipe the fixture and bath set components with a soft, dry cloth.
• Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
• For glass shades, use a mild glass cleaner applied to a cloth, not directly to the shade.

Bulb Replacement:

• Ensure the power is off at the circuit breaker before replacing bulbs.
• Allow bulbs to cool completely before touching them.
• Unscrew the old bulb counter-clockwise.
• Screw in the new bulb clockwise. Use A19 type incandescent bulbs, maximum 60-Watt.

Troubleshooting

Specifications

Warranty and Support

This product is manufactured by Overstock. For specific warranty information, please refer to the documentation included with your purchase or contact Overstock customer service directly. Warranty terms typically cover defects in materials and workmanship for a specified period from the date of purchase.

For technical support or assistance with parts, please contact the retailer where the product was purchased. If purchased from Amazon, you may contact BED BATH & BEYOND, the seller for this product.

Online Resources: For additional information or frequently asked questions, please visit the official Overstock website or the product page on the retailer's website.