Giantex Full Bed Frame with Ottoman Storage

Introduction

The Giantex Full Bed Frame with Ottoman Storage is designed to provide a comfortable sleeping surface and integrated storage. This manual contains important information for the safe assembly, proper use, and routine maintenance of your bed frame. Please read these instructions thoroughly before assembly and retain them for future reference.

Safety Information

• Weight Capacity: Do not load more than 880 pounds (399 kg) on the bed frame. The ottoman bench has a separate weight capacity of 440 pounds (200 kg). Exceeding these limits may cause damage or injury.
• Assembly: Always follow the assembly instructions carefully. Incorrect assembly can lead to instability, structural failure, or pinch point hazards.
• Children: Keep children away from the assembly area. Small parts can be a choking hazard.
• Tools: Use appropriate tools as specified in the assembly guide.
• Placement: Place the bed frame on a level, stable surface.

Package Contents

Verify that all components listed below are present and undamaged before beginning assembly. If any parts are missing or damaged, please contact customer support.

• Bed Frame Components (Headboard, Side Rails, Footboard with Ottoman, Slats, Support Legs)
• Hardware Pack (Screws, Bolts, Washers, Allen Wrench)
• Instruction Manual (This document)

Setup and Assembly Instructions

Assembly of the Giantex Full Bed Frame typically requires two adults and can be completed in approximately one hour. Refer to the detailed step-by-step instructions provided in the separate assembly guide included in your package for specific diagrams and hardware identification.

1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
2. Assemble Headboard: Attach the headboard legs to the upholstered headboard panel using the specified hardware.
3. Connect Side Rails: Secure the side rails to the headboard and the footboard (which includes the ottoman storage).
4. Install Support Legs: Attach the middle support legs to the center rail of the bed frame. Ensure adjustable foot pads are correctly oriented.
5. Place Slats: Position the wooden slats evenly across the bed frame and secure them according to the instructions. The dense slats eliminate the need for a box spring.
6. Final Tightening: Once all components are in place, carefully tighten all screws and bolts. Do not overtighten.

Operating Instructions

The integrated ottoman at the foot of the bed provides convenient storage for various items.

• Accessing Storage: To open the ottoman, gently lift the upholstered lid. The lid is supported by strong metal hinges for smooth operation.
• Closing Storage: To close, lower the lid until it rests securely on the frame. Ensure no items are obstructing the closing mechanism.
• Using as a Bench: When the lid is closed, the ottoman can be used as a bench. Adhere to the 440 lbs (200 kg) weight limit for the ottoman.

Maintenance

• Cleaning: For general cleaning, wipe the upholstered surfaces with a dry cloth. Avoid using harsh chemicals or abrasive cleaners.
• Hardware Check: Periodically inspect all screws, bolts, and connections to ensure they remain tight. Retighten if necessary to maintain stability.
• Avoid Moisture: Keep the bed frame away from excessive moisture or direct sunlight to prevent material degradation.

Troubleshooting

• Instability/Wobbling: If the bed frame feels unstable or wobbles, check that all assembly hardware (screws, bolts) is fully tightened. Ensure the bed is on a level surface and adjust the foot pads if needed.
• Squeaking Noises: Squeaking can often be resolved by tightening all hardware connections. Ensure slats are properly seated and not rubbing against the frame.
• Ottoman Lid Not Closing Properly: Check for any obstructions inside the ottoman compartment that might prevent the lid from closing completely. Inspect hinges for damage or misalignment.
• Missing or Damaged Parts: If you discover any missing or damaged parts upon opening the package, do not proceed with assembly. Contact Giantex customer support immediately for assistance.

Specifications

Warranty and Support

Giantex offers a 90-day easy return policy for this product. For any questions, concerns, or assistance with assembly or parts, please contact Giantex customer support. You can find more information and contact details by visiting the official Giantex store:

Visit the Giantex Store on Amazon