Introduction
This manual provides essential information for the proper installation, maintenance, and care of your Titunjian 2 Pcs Wall Sculptures Metal Wall Art. Please read these instructions carefully before installation to ensure safe and correct usage.
Image: The two pieces of Titunjian metal wall art, each depicting a stylized golden plant with multiple leaves, framed within a rectangular border.
The Titunjian Metal Wall Art is designed to enhance interior spaces with its modern aesthetic. Crafted from high-quality iron, these pieces feature a hollow-out design with 3D lines, providing a sophisticated and artistic touch to any room.
Safety Information
- Ensure the wall surface is suitable for hanging decorative items and can support the weight of the sculpture.
- Use appropriate wall anchors and screws for your specific wall type (e.g., drywall, plaster, concrete).
- Keep out of reach of children to prevent accidental injury.
- Avoid hanging in areas where it may be frequently bumped or exposed to extreme temperatures or humidity.
Package Contents
Upon unpacking, please verify that all components are present and undamaged:
- 2 x Titunjian Metal Wall Sculptures (Type B, 33.5 x 11.8 Inch)
- Installation hardware (may vary, typically includes screws and wall anchors)
Setup and Installation
The Titunjian Metal Wall Art is designed for convenient installation with pre-drilled hanging holes. No assembly of the art pieces themselves is required.
Tools Required (Not Included):
- Pencil
- Measuring tape
- Drill (with appropriate drill bit for wall anchors)
- Screwdriver
- Level
Installation Steps:
- Determine Placement: Choose a suitable location on your wall. Consider the overall aesthetic and ensure there is enough space for both pieces if hanging them together.
- Measure and Mark: Hold one sculpture against the wall at your desired height and position. Use a pencil to mark the locations of the two hanging holes at the top of the frame. Repeat for the second sculpture, ensuring symmetrical placement if desired.
- Drill Pilot Holes: Using a drill with a bit appropriate for your wall type and the provided wall anchors, drill pilot holes at the marked locations.
- Insert Wall Anchors: Gently tap the wall anchors into the pilot holes until they are flush with the wall surface.
- Install Screws: Drive screws into the wall anchors, leaving a small portion of the screw head exposed to allow the sculpture to hang securely.
- Hang the Sculptures: Carefully align the hanging holes on the back of each sculpture with the exposed screw heads and lower the sculptures into place. Ensure they are stable and level.
Image: A detailed view of the integrated hanging bracket located at the top corner of the metal frame, designed for easy wall mounting.
Image: The two metal wall sculptures displayed in a dining room setting, positioned above a dining table, demonstrating a typical installation.
Image: The two metal wall sculptures displayed in a living room setting, positioned above a sofa, showcasing their decorative impact.
Maintenance
To maintain the appearance and longevity of your metal wall art, follow these simple care instructions:
- Cleaning: Gently wipe the surface with a soft, dry cloth to remove dust. For more stubborn marks, a slightly damp cloth can be used, followed immediately by a dry cloth to prevent water spots.
- Avoid Harsh Chemicals: Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the finish.
- Indoor Use Only: This product is designed for indoor use. Exposure to outdoor elements can lead to rust and fading.
Image: A close-up view of one of the golden metal leaves, highlighting its delicate cut-out patterns and the smooth, glossy finish.
Troubleshooting
- Issue: Metal leaves appear slightly bent or deformed.
- Solution: The 3D metal leaves are designed to be tough and elastic. If any deformation occurs during shipping or handling, you may gently and carefully adjust them by hand to restore their intended shape.
- Issue: Sculpture does not hang level.
- Solution: Ensure that the marked points for drilling were level. Adjust the screws slightly or re-drill if necessary to achieve a perfectly level hang. A spirit level is recommended during installation.
Specifications
| Product Name | Titunjian Metal Wall Art |
| Model | Type B |
| Dimensions (each piece) | 33.5 x 11.8 x 0.2 inches (85 x 30 x 0.5 cm) |
| Material | High-quality Iron |
| Color | Golden |
| Quantity | 2 Pcs per set |
Image: A diagram illustrating the precise dimensions of one metal wall art piece, showing a height of 33.5 inches (85 cm) and a width of 11.8 inches (30 cm).
Warranty and Support
For information regarding warranty coverage or product support, please refer to the retailer's return policy or contact the manufacturer directly through their official channels. Please retain your proof of purchase for any warranty claims.
