Vitalograph COPD-6 Screener BT User Manual

1. Introduction

This manual provides essential information for the safe and effective operation of the Vitalograph COPD-6 Screener BT. The Vitalograph COPD-6 is an electronic COPD screening device designed to ascertain the obstruction index and the FEV1/FEV6 ratio, thereby assisting in the detection of potential COPD diseases. It identifies individuals at risk of COPD at the pre-symptomatic stage and screens out those whose FEV1 is normal.

Please read this manual thoroughly before using the device and retain it for future reference.

Image 1: Front view of the Vitalograph COPD-6 Screener BT device.

2. Important Safety Information

Always adhere to the following safety precautions to ensure proper operation and prevent injury or damage to the device.

• Use the device only as described in this manual.
• Do not immerse the device in water or other liquids.
• Keep the device away from extreme temperatures and direct sunlight.
• Do not attempt to open or repair the device. Refer all servicing to qualified personnel.
• Ensure batteries are inserted correctly according to polarity markings.
• Dispose of batteries and the device according to local regulations.
• This device is intended for screening purposes and should not replace a full medical diagnosis.

3. Device Components

Familiarize yourself with the main parts of your Vitalograph COPD-6 Screener BT.

Image 2: Top-down view showing the mouthpiece and display.

Image 3: Side view of the device, highlighting its ergonomic design.

Image 4: Device with a disposable mouthpiece attached for use.

Image 5: Device with a larger, alternative mouthpiece attached.

• Mouthpiece: Where the user exhales.
• Display Screen: Shows readings, indicators, and menu options.
• Control Buttons: For navigation and selection.
• Bluetooth Indicator: Shows connection status.
• Battery Compartment: Located on the back (not shown in images, but implied).

4. Setup

4.1. Battery Installation

1. Locate the battery compartment on the back of the device.
2. Open the compartment cover.
3. Insert 2 AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. Close the battery compartment cover securely.

4.2. Attaching the Mouthpiece

1. Select a clean, disposable mouthpiece.
2. Align the mouthpiece with the opening on the device.
3. Gently push the mouthpiece onto the device until it is firmly seated.

4.3. Initial Power On and Bluetooth Pairing

1. Press the power button to turn on the device.
2. The device will display initial setup options or be ready for use.
3. To pair with a computer or mobile device, ensure Bluetooth is enabled on both the COPD-6 Screener BT and the receiving device.
4. Open the Vitalograph Reports Software (included) on your computer or the Vitalograph app on your mobile device.
5. Follow the on-screen instructions within the software/app to complete the pairing process. The Bluetooth indicator on the COPD-6 will confirm successful connection.

5. Operating Instructions

5.1. Performing a Test

1. Ensure the device is powered on and a clean mouthpiece is attached.
2. Sit upright and relax.
3. Take a deep breath, filling your lungs completely.
4. Place your lips tightly around the mouthpiece, ensuring no air leaks.
5. Exhale as hard and as fast as you can, emptying your lungs completely. Continue exhaling for at least 6 seconds.
6. The device will display the FEV1, FEV6, ratio, percent predicted, obstructive index, COPD classification, and lung age.
7. Repeat the test as necessary, typically three times, to ensure consistent and accurate readings.

5.2. Interpreting Results

The device displays key spirometry parameters. The GOLD COPD classification (Stage I – IV) is shown to help recognize the need for a change in the patient’s management plan. Results are automatically sent to the paired software/app after each blow for detailed reporting and analysis.

• FEV1: Forced Expiratory Volume in 1 second.
• FEV6: Forced Expiratory Volume in 6 seconds.
• FEV1/FEV6 Ratio: An important indicator for COPD screening.
• Obstructive Index: Based on a percentage of predicted values.
• Lung Age: An estimate of lung health compared to chronological age.

6. Maintenance and Care

6.1. Cleaning the Device

• Wipe the exterior of the device with a soft, damp cloth.
• Do not use abrasive cleaners or immerse the device in water.
• The mouthpiece should be disposable and replaced for each user to maintain hygiene.

6.2. Battery Replacement

When the battery indicator appears on the display, replace the batteries as described in the "Battery Installation" section (4.1). Always use new AAA alkaline batteries.

6.3. Storage

Store the device in its carry pouch in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

8. Specifications

9. Warranty and Support

9.1. Warranty Information

Vitalograph products are manufactured to high standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Vitalograph website.

9.2. Customer Support

For technical assistance, troubleshooting not covered in this manual, or service inquiries, please contact Vitalograph customer support. Contact details can typically be found on the Vitalograph website or on the product packaging.

Website: www.vitalograph.co.uk