MEIKEE 15W RGBW Low Voltage Landscape Lights Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your MEIKEE 15W RGBW Low Voltage Landscape Lights. Please read these instructions thoroughly before use and retain them for future reference.

2. Safety Information

• Ensure the power supply is disconnected before installation or maintenance.
• This product operates on DC/AC 12-24V low voltage. Do not connect directly to 120V AC power without a compatible low voltage transformer.
• Low voltage wiring and transformers are not included and must be purchased separately.
• Ensure all connections are secure and waterproof to prevent electrical hazards.
• Do not attempt to modify or disassemble the lights, as this may void the warranty and create safety risks.
• Keep children and pets away from the installation area during setup.

3. Package Contents

Verify that all items listed below are present in your package:

• 12 x 15W RGBW Landscape Lights
• 24 x Wire Connectors
• 2 x Remote Controls
• 1 x Instruction Manual (this document)
• 1 x Screw Pack (for wall mounting)

4. Setup

4.1. Installation Methods

Your MEIKEE landscape lights offer two primary installation methods: ground insertion or wall mounting.

• Ground Insertion: Attach the provided stake to the light fixture. Push the stake firmly into the ground in your desired location.
• Wall Mounting: Use the included bracket and screws to secure the light fixture to a wall or fence. Adjust the light head to the desired angle.

4.2. Wiring Instructions

The lights require a DC/AC 12-24V low voltage power supply. A low voltage transformer and low voltage wiring are not included and must be acquired separately.

1. Prepare your low voltage wiring by separating the two halves of the power cable.
2. Disassemble the wire connector by unscrewing the cap.
3. Insert one half of the power cable through the large cap of the connector.
4. Align the power cable with the pin inside the connector and screw the cap back on firmly to pierce the cable and establish contact.
5. Repeat the process for the other half of the power cable and the second part of the connector.
6. Connect the light's wires to the prepared wire connectors, ensuring a secure and tight connection.
7. Test the connection to ensure the wire does not come out easily.

4.3. Setup Videos

For a visual guide on installation and features, please refer to the following videos:

5. Operating Instructions

Your MEIKEE landscape lights are controlled via the included 29-key remote control. Ensure the remote has batteries installed (batteries included in the screw pack).

5.1. Remote Control Functions

• Power On/Off: Use the red power button to turn the lights on or off.
• Single Colors: Select from 10 single colors directly using the color buttons.
• Adjustable Brightness: Use the brightness up/down buttons to adjust the intensity of the selected color (25%-100%).
• Flash/Smooth Mode: Toggle between flashing and smooth transitions for single colors.
• Multi-Color Working Modes: Choose from 10 multi-color modes with adjustable speed for dynamic lighting effects.
• Timer Function: Set the lights to automatically turn off after 2, 4, or 6 hours using the dedicated timer buttons.
• Memory Function: The lights will remember your last setting (color, brightness, mode) when turned off and on again, eliminating the need to reset.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your landscape lights.

• Cleaning: Periodically wipe the light fixtures with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners.
• Waterproofing: The lights are IP66 waterproof, designed to withstand various weather conditions. Ensure all connections are tightly sealed during installation to maintain this rating.
• Heat Dissipation: The aluminum housing is designed for efficient heat dissipation. Ensure the fixtures are not covered or obstructed to allow for proper airflow.
• Cable Inspection: Regularly inspect the low voltage cables for any signs of damage, fraying, or wear. Replace damaged cables immediately to prevent electrical hazards.

7. Troubleshooting

If you encounter issues with your MEIKEE landscape lights, refer to the following common troubleshooting steps:

• Lights Not Turning On:
  • Check the power supply to the low voltage transformer.
  • Ensure all wire connections are secure and properly pierced.
  • Verify the remote control batteries are functional and correctly inserted.
• Remote Not Responding:
  • Ensure there are no obstructions between the remote and the lights.
  • Replace the remote control batteries.
  • Confirm you are within the maximum control distance (12 meters / 39.3 feet).
• Inconsistent Lighting/Flickering:
  • Inspect wire connections for looseness or corrosion.
  • Check the low voltage wiring for damage.
  • Ensure the transformer is adequately sized for the total wattage of connected lights.
• Water Inside Fixture:
  • While the lights are IP66 rated, extreme conditions or improper installation can sometimes lead to water ingress. If this occurs, disconnect power immediately and contact customer support.

8. Specifications

9. Warranty and Support

MEIKEE products are covered by a 2-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

For technical support, warranty claims, or any questions regarding your product, please contact MEIKEE customer service. You can typically reach us via email through the Amazon platform or by using the contact information provided in your product packaging.

We aim to provide a timely response within 24 hours.