Introduction
This manual provides detailed instructions for the safe assembly, operation, and maintenance of your Disney Baby Minnie Mouse Simple Fold LX Travel System. This system includes a stroller and a rear-facing infant car seat, designed for convenience and safety. Please read all instructions carefully before use and retain this manual for future reference.
Figure 1: Disney Baby Minnie Mouse Simple Fold LX Travel System (Stroller and Car Seat)
Important Safety Information
WARNING: Failure to follow these warnings and instructions could result in serious injury or death.
- Always secure your child with the 5-point harness.
- Never leave your child unattended in the stroller or car seat.
- Avoid serious injury from falling or sliding out. Always use the restraint system.
- The car seat is designed for infants weighing 4-30 lbs (1.8-13.6 kg) and up to 32 inches (81 cm) in height.
- The stroller is suitable for children up to 50 lbs (22.7 kg).
- Ensure the stroller is fully locked before placing a child in it.
- Do not overload the storage basket; maximum weight capacity is typically 10 lbs (4.5 kg).
- Do not use accessories or replacement parts other than those approved by the manufacturer.
- Read all labels on the product before use.
Package Contents
Verify that all components are present before assembly:
- Stroller Frame with Seat
- Infant Car Seat
- Car Seat Base
- Front Wheels (2)
- Rear Wheels (2)
- Parent Tray
- Child Snack Tray
- Instruction Manual
Setup and Assembly
1. Stroller Assembly
- Unfolding the Stroller: Release the folding latch (if present) and lift the handle until the stroller frame locks into place. Ensure both sides are securely latched.
- Attaching the Wheels:
- Slide the front wheels onto the front leg posts until they click securely. Pull on the wheels to ensure they are locked.
- Attach the rear wheels by pushing them onto the rear axle until they click.
- Attaching the Parent Tray: Align the parent tray with the slots on the stroller handle and push down until it clicks into place.
- Attaching the Child Snack Tray: Align the child snack tray with the slots on the stroller frame and push down until it clicks into place.
Figure 2: Parent Tray Installation
Figure 3: Child Snack Tray Installation
2. Car Seat Base Installation (Vehicle)
Refer to your car seat manual for complete installation instructions. The car seat base can be installed using your vehicle's LATCH system or the vehicle's seat belt.
- LATCH Installation: Locate your vehicle's lower anchor bars. Attach the LATCH connectors from the car seat base to the vehicle's anchor bars. Press firmly on the base and tighten the LATCH strap until the base is secure and does not move more than 1 inch side-to-side or front-to-back at the belt path.
- Seat Belt Installation: Route the vehicle's lap and shoulder belt through the designated belt path on the car seat base. Buckle the seat belt and remove all slack by pressing firmly on the base and pulling the shoulder belt. Lock the vehicle's seat belt (refer to your vehicle owner's manual).
- Ensure the recline indicator on the car seat base is within the acceptable range for your infant's weight and age.
Operating Instructions
1. Using the Stroller
- Securing Your Child: Place your child in the stroller seat and fasten the 5-point harness. Adjust the shoulder straps to the appropriate height and tighten all straps snugly against your child.
- Reclining the Seat: Locate the recline mechanism on the back of the seat. Squeeze the lever or press the button and adjust the seat to the desired recline position. Ensure it locks into place.
- Canopy Adjustment: Extend or retract the multi-panel sun canopy as needed for sun protection. The peekaboo window allows you to check on your child without disturbing them.
- Brakes: To engage the brakes, press down on the brake levers located on the rear wheels. Ensure the stroller does not move. To release, lift the levers.
- Storage Basket: The large, easy-access storage basket beneath the seat can hold essential items. Do not exceed the maximum weight limit.
Figure 4: Stroller in Use
Figure 5: Canopy with Peekaboo Window
2. Using the Infant Car Seat
- Securing Your Infant: Place your infant in the car seat. Ensure the shoulder straps are at or below your infant's shoulders. Fasten the 5-point harness and tighten until snug. The chest clip should be at armpit level.
- Car Seat into Base: Align the car seat with the installed car seat base. Lower the car seat onto the base until it clicks securely into place. Pull up on the car seat to ensure it is locked.
- Car Seat onto Stroller (QuickClick): The QuickClick system allows for easy attachment. Align the car seat with the stroller's child tray or designated car seat receivers. Lower the car seat until it clicks securely into place. Pull up on the car seat to ensure it is locked.
Figure 6: Attaching Car Seat to Stroller
3. Folding and Storage
The Simple Fold LX Travel System features a 1-hand Lift-to-Fold mechanism for compact storage.
- Remove your child from the stroller.
- Ensure the seat is in the upright position and the canopy is retracted.
- Locate the folding strap or handle, typically in the center of the seat.
- Lift the strap/handle upwards with one hand. The stroller will fold compactly.
- Secure the folding latch (if it does not automatically engage). The stroller is designed to be self-standing when folded.
Figure 7: Stroller Folded for Storage
Maintenance
- Cleaning Fabric: Spot clean fabric with a mild soap and warm water. Air dry. Do not use bleach.
- Cleaning Frame: Wipe the metal frame with a soft, damp cloth.
- Wheels: Periodically check wheels for debris and ensure they rotate freely. Lubricate axles with a light oil if necessary.
- Harness: Check harness straps and buckles regularly for wear or damage.
- Storage: Store the travel system in a dry, cool place away from direct sunlight.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stroller difficult to fold/unfold. | Folding mechanism obstructed or not fully engaged. | Ensure no items are blocking the folding mechanism. Apply firm, even pressure when lifting the fold strap. |
| Wheels squeak or do not turn smoothly. | Debris in wheel axles or lack of lubrication. | Clean wheels and axles. Apply a small amount of silicone-based lubricant. |
| Car seat does not click into stroller/base. | Misalignment or obstruction. | Ensure car seat is correctly aligned with receivers. Check for any fabric or debris blocking the connection points. |
| Harness straps are difficult to adjust. | Straps twisted or buckle mechanism obstructed. | Untwist straps. Ensure buckle is free of debris. Refer to the car seat manual for specific harness adjustment instructions. |
Specifications
- Model Number: TR447GNU
- Brand: Disney
- Color: Minnie Dot Party
- Material: Polyester, Aluminum Frame
- Stroller Weight Capacity: Up to 50 lbs (22.7 kg)
- Car Seat Weight Capacity: Rear-facing from 4-30 lbs (1.8-13.6 kg)
- Car Seat Height Limit: Up to 32 inches (81 cm)
- Harness Type: 5-Point Harness (Stroller & Car Seat)
- Installation Type (Car Seat Base): LATCH or Vehicle Seat Belt
- Item Weight (Travel System): Approximately 29 lbs (13.2 kg)
- Manufacturer: Dorel Juvenile Group
- UPC: 884392953089
Warranty and Support
This product is manufactured by Dorel Juvenile Group under the Disney brand. For specific warranty information, please refer to the warranty card included with your product or contact Dorel Juvenile Group customer service.
For assistance with parts, service, or questions regarding your Disney Baby Minnie Mouse Simple Fold LX Travel System, please contact the manufacturer's customer support. Contact information can typically be found on the product packaging or the manufacturer's official website.
Protection plans are available for purchase separately. For details on 2-Year or 3-Year Protection Plans, please refer to the retailer where the product was purchased.
