1. Introduction
The AXA Blueline Rear Dynamo Light is a compact and efficient taillight designed for bicycles, perfectly fitting the modern trend towards lighter and slimmer bike aesthetics. Its design ensures suitability for nearly all luggage carriers. Featuring advanced lightguide technology, it provides optimal safety through superior light distribution. Side lighting enhances visibility to crossing traffic, significantly improving rider safety. An integrated steady light function keeps the light on for 4 minutes even when the bicycle is stationary, providing continuous visibility. This light is dynamo operated and includes an integrated reflector.
Figure 1: The AXA Blueline Rear Dynamo Light, showcasing its compact design and integrated reflector.
2. Key Features
- Dynamo Operated: Powers directly from your bicycle's dynamo, eliminating the need for batteries.
- 6V E-bike Battery Compatible: Can also be powered by a 6V E-bike battery for versatile use.
- Integrated Reflector: Enhances passive safety by reflecting light from other sources.
- 50 mm Mounting Distance: Designed for standard 50mm mount spacing on luggage carriers.
- Visible from the Side: Special lightguide technology ensures visibility from the side, increasing safety in traffic.
- Steady Light Function: Provides 4 minutes of light when stationary, maintaining visibility during stops.
3. Setup and Installation
3.1 Mounting the Light
The AXA Blueline Rear Dynamo Light is designed for seat mount installation, typically on a bicycle's luggage carrier. It features a standard mounting distance of 50 mm between the two mounting points.
- Identify the mounting points on your bicycle's luggage carrier. These should be two holes spaced 50 mm apart.
- Align the light's mounting holes with those on the carrier.
- Secure the light using appropriate screws and nuts (not included, typically supplied with the carrier or bicycle). Ensure the light is firmly attached and does not wobble.
3.2 Wiring the Dynamo Connection
Connect the light to your bicycle's dynamo system. Ensure proper polarity if specified by your dynamo or E-bike system. The light is compatible with standard bicycle dynamos and 6V E-bike batteries.
- Locate the dynamo output wires, usually one for power and one for ground.
- Connect the power wire from the dynamo to the corresponding input on the Blueline light.
- Connect the ground wire from the dynamo to the ground input on the light.
- Ensure all connections are secure and protected from water and debris.
4. Operation
4.1 Activating the Light
The AXA Blueline Rear Dynamo Light operates automatically when connected to a functioning dynamo and the bicycle is in motion. As the wheels turn, the dynamo generates electricity, powering the light.
4.2 Steady Light Function
This light features an integrated steady light function. After you stop cycling, the light will remain illuminated for approximately 4 minutes. This ensures continued visibility at intersections or during brief stops, enhancing safety.
5. Maintenance
To ensure the longevity and optimal performance of your AXA Blueline Rear Dynamo Light, follow these simple maintenance guidelines:
- Cleaning: Regularly wipe the light's lens and housing with a soft, damp cloth to remove dirt and grime. Avoid abrasive cleaners or solvents that could damage the plastic.
- Connections: Periodically check the electrical connections to the dynamo or E-bike battery to ensure they are secure and free from corrosion.
- Mounting: Verify that the light remains securely mounted to your bicycle's carrier. Tighten any loose screws as needed.
- Inspection: Inspect the light for any physical damage, such as cracks in the housing or lens, which could compromise its performance or water resistance.
Note: The product is listed as "Not Water Resistant". While it is designed for outdoor use, avoid submerging it in water or exposing it to extreme water pressure.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on when cycling. |
|
|
| Light is dim or flickers. |
|
|
| Steady light function does not work. |
|
|
7. Specifications
| Attribute | Detail |
|---|---|
| Model Name | AXA Blueline Rear Dynamo Light |
| Model Number | 93961495US |
| Brand | AXA |
| Color | Black |
| Material | Multi |
| Power Source | Dynamo, 6V E-bike Battery Compatible |
| Water Resistance Level | Not Water Resistant |
| Mounting Type | Seat Mount |
| Mounting Distance | 50 mm |
| Number of Settings | 1 (On/Off via dynamo) |
| Auto Part Position | Rear |
| Integrated Features | Reflector, Steady Light Function (4 minutes) |
| Item Weight | Approximately 40g (as per product description) |
8. Warranty and Support
8.1 Limited Warranty
The AXA Blueline Rear Dynamo Light comes with a Limited Warranty. For specific details regarding the terms, conditions, and duration of the warranty, please refer to the warranty card included with your purchase or contact AXA customer service directly. This warranty typically covers manufacturing defects and material flaws under normal use.
8.2 Customer Support
Should you encounter any issues not covered in the troubleshooting section, or require further assistance, please contact AXA customer support. Have your product model number (93961495US) and purchase information ready when contacting support.
For the most up-to-date contact information, please visit the official AXA website or refer to the packaging of your product.
