Introduction
This user manual provides comprehensive instructions for the installation, operation, and maintenance of your Ozone Fort Safe AB - 66 Biometric Safe Locker. This safe is designed for secure storage of valuables in home, office, and warehouse environments, featuring biometric, keypad, and key access options. It is constructed from strong metal steel with a powder-coated finish, equipped with five heavy-duty SS shooting bolts and a five-spoke handle for robust security.
Figure 1: Ozone Fort Safe AB-66 Biometric Safe Locker
Product Features
- Digital keypad with LED screen for clear visibility and operation.
- Multiple access modes: Fingerprint, User Password, and Master Password.
- Emergency key available for manual override.
- Low battery indicator to alert users when power is low.
- Equipped with five heavy-duty SS shooting bolts for enhanced security.
- Fingerprint reader capable of registering up to 50 unique fingerprints.
- Five-spoke handle for smooth opening and closing of the door.
- Keypad auto-freeze feature for 5 minutes after 3 consecutive incorrect password attempts, preventing unauthorized access.
Figure 2: Access Modes
Setup and Installation
Unpacking
Carefully remove the safe from its packaging. Inspect the safe for any signs of damage during transit. Retain all packaging materials until you are satisfied with the product.
Battery Installation
The safe requires 4 AA batteries (included). Locate the battery compartment, typically on the inside of the safe door. Insert the batteries, ensuring correct polarity (+/-). The LED screen should illuminate upon successful installation.
Mounting the Safe
The Ozone Fort Safe AB-66 is designed for floor mounting and comes with pre-drilled holes for easy installation. For optimal security, it is highly recommended to bolt the safe to a solid surface.
- Choose a secure and discreet location for the safe.
- Open the safe door and locate the pre-drilled holes on the bottom or back panel.
- Position the safe and mark the drilling points on the floor or wall using a pencil.
- Move the safe and drill pilot holes at the marked locations using an appropriate drill bit for your surface (concrete, wood, etc.).
- Reposition the safe over the drilled holes.
- Secure the safe using appropriate anchor bolts (not included, as type depends on mounting surface) through the pre-drilled holes. Tighten all bolts securely.
Figure 3: Pre-drilled Holes for Installation
Operating Instructions
Initial Setup and Opening
Upon first use, the safe can be opened using the emergency key. Insert the emergency key into the keyhole, turn it, and simultaneously rotate the five-spoke handle to open the door.
Setting the Master Password
- With the door open, press the internal reset button (usually a small red button located near the hinge).
- The LED screen will display "PROG" or similar, indicating it's ready for programming.
- Enter your desired 4-8 digit master password on the keypad.
- Press the "#" or "ENTER" button to confirm. The screen will display "GOOD" or "SUCCESS".
- Test the new master password with the door open before closing it.
Setting User Passwords
The safe supports multiple user passwords. Follow a similar procedure as setting the master password, but typically there's a specific sequence or button to initiate user password programming (refer to the on-screen prompts or a dedicated user password button if available).
Registering Fingerprints
The safe can store up to 50 fingerprints. The process usually involves:
- Press the fingerprint registration button (if available) or enter a specific code on the keypad to enter fingerprint programming mode.
- Place the desired finger on the fingerprint scanner. You may be prompted to lift and place the finger multiple times from different angles to ensure accurate registration.
- The screen will confirm successful registration. Repeat for additional fingerprints.
Opening the Safe
- Using Password: Enter your password on the keypad, then press "#" or "ENTER". Rotate the handle within a few seconds to open.
- Using Fingerprint: Place your registered finger on the scanner. Once recognized, rotate the handle within a few seconds to open.
- Using Emergency Key: Insert the emergency key and turn it, then rotate the handle.
Closing and Locking the Safe
Close the safe door firmly. Rotate the five-spoke handle counter-clockwise until the bolts are fully extended and the door is securely locked. The safe will automatically lock once the handle is turned.
Maintenance
Battery Replacement
When the low battery indicator appears on the LED screen, replace all 4 AA batteries promptly. Use high-quality alkaline batteries for optimal performance. Do not mix old and new batteries or different battery types.
Cleaning
Clean the exterior of the safe with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish or electronic components. Ensure the keypad and fingerprint scanner are kept clean and free of dust or debris.
General Care
Regularly check the door hinges and locking bolts for smooth operation. Do not force the handle if the door is stiff. Keep the emergency keys in a secure location outside the safe.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Safe does not open with password/fingerprint. | Incorrect password/fingerprint, low batteries, keypad frozen. | Verify password, re-scan finger, replace batteries, wait 5 minutes if keypad is frozen. Use emergency key. |
| LED screen is blank. | Dead batteries. | Replace all 4 AA batteries. |
| Safe door does not close properly. | Obstruction, misaligned bolts. | Check for obstructions around the door frame. Ensure bolts retract fully before closing. |
| Cannot register new fingerprints. | Scanner dirty, memory full, incorrect procedure. | Clean scanner, delete old fingerprints if memory is full, review registration steps. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | ABS0002 |
| Capacity | 78 Litres |
| Dimensions (H x W x D) | 55 cm x 46 cm x 36 cm (approx.) |
| Weight | 64.3 kg |
| Lock Type | Biometric, Digital Keypad, Emergency Key |
| Material | Metal (Steel) |
| Finish | Black Structure Matt |
| Batteries | 4 x AA (included) |
| Mounting | Floor Mount (pre-drilled holes) |
| Fingerprint Capacity | Up to 50 fingerprints |
Figure 4: Product Dimensions and Capacity
Warranty and Support
The Ozone Fort Safe AB-66 comes with a warranty card included in the package. Please refer to the warranty card for specific terms and conditions, including warranty period and coverage details.
For technical support, troubleshooting assistance, or warranty claims, please contact Ozone customer service. Contact information can typically be found on the warranty card or the official Ozone website. When contacting support, please have your model number (ABS0002) and purchase details ready.
Included Components: User Manual, Warranty Card, 1 Safe.
