1. Product Overview
The TrolMaster TS-1 Thermostat Station is a dedicated module designed for precise temperature control within a cool-only conventional HVAC system. It integrates seamlessly with the TrolMaster Hydro-X Control System, providing accurate temperature monitoring and regulation to maintain optimal environmental conditions. This station is engineered for reliability and ease of use, ensuring your cooling system operates efficiently.
Figure 1.1: Angled view of the TrolMaster TS-1 Thermostat Station, displaying its screen with temperature readings.
2. Features
- Cool-Only HVAC Compatibility: Specifically designed to control conventional cooling systems.
- Hydro-X System Integration: Connects directly to the TrolMaster Hydro-X Control System for centralized management.
- Digital Display: Clear LCD screen shows setpoint, current temperature, and operational status.
- Push-Button Controls: Intuitive buttons for easy temperature adjustments and fan control.
- Compact Design: Space-saving form factor for versatile installation.
3. Package Contents
Verify that all items are present in the package before proceeding with installation.
- 1 x TrolMaster TS-1 Thermostat Station
Figure 3.1: Side view of the TS-1, illustrating its compact design and mounting points.
4. Setup and Installation
Follow these steps for proper installation of your TS-1 Thermostat Station.
4.1 Mounting the TS-1
- Choose a suitable location for the TS-1, away from direct sunlight, heat sources, or drafts, which could affect temperature readings.
- Secure the TS-1 to a wall or flat surface using appropriate screws through the designated mounting holes.
4.2 Wiring to HVAC System
The TS-1 connects to your conventional cool-only HVAC system using standard thermostat wiring.
Figure 4.1: Rear view of the TS-1, showing the R, W, Y, G terminals for HVAC wiring.
- R (Power): Connect to the 24VAC common wire from your HVAC transformer.
- W (Heat): Not used for cool-only systems. Ensure this terminal is not connected.
- Y (Cool): Connect to the cooling call wire from your HVAC system.
- G (Fan): Connect to the fan control wire from your HVAC system.
Important: Always turn off power to your HVAC system at the circuit breaker before performing any wiring. If you are unsure about wiring, consult a qualified electrician or HVAC technician.
4.3 Connecting to Hydro-X Control System
The TS-1 connects to your Hydro-X Control System via a standard RJ12 cable.
Figure 4.2: Connection diagram of the TS-1 to the Hydro-X Control System.
- Connect one end of the RJ12 cable to the port labeled 'Addressing' on the TS-1.
- Connect the other end of the RJ12 cable to an available device port on your Hydro-X Control System.
- Once connected, the Hydro-X system should automatically detect the TS-1.
5. Operating Instructions
The TS-1 operates in conjunction with your Hydro-X Control System. Basic settings can be viewed and adjusted directly on the TS-1 unit.
5.1 Display Information
The TS-1 display provides the following information:
- Setpoint: The desired temperature you have set.
- Current: The current ambient temperature detected by the TS-1.
- Cool On/Off: Indicates if the cooling system is currently active.
- Fan: Indicates the status of the fan (On/Auto).
5.2 Adjusting Setpoint Temperature
Use the up/down arrow buttons next to the display to adjust the desired temperature setpoint. The Hydro-X system will then manage the cooling system to maintain this temperature.
5.3 Fan Control
Press the 'FAN' button to cycle through fan modes (e.g., Auto, On). Refer to your Hydro-X Control System manual for detailed fan operation settings.
6. Maintenance
The TS-1 Thermostat Station requires minimal maintenance to ensure optimal performance.
- Cleaning: Periodically wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Ventilation: Ensure that the ventilation slots on the unit are not obstructed to allow for proper airflow and accurate temperature sensing.
7. Troubleshooting
If you encounter issues with your TS-1 Thermostat Station, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| TS-1 display is blank. | No power to the unit or Hydro-X system. | Check power supply to the Hydro-X system and ensure the RJ12 cable is securely connected. Verify HVAC system power. |
| HVAC system not responding to TS-1. | Incorrect wiring; Hydro-X system issue; HVAC system fault. | Verify all wiring connections (R, Y, G) are correct and secure. Check the status of your Hydro-X Control System. Consult an HVAC technician if the HVAC system itself is not functioning. |
| Inaccurate temperature readings. | Sensor obstructed or located in an unsuitable environment. | Ensure the TS-1's ventilation slots are clear. Relocate the TS-1 if it is in direct sunlight, near a heat source, or in a draft. |
For further assistance, please refer to the Hydro-X Control System manual or contact FGI customer support.
8. Specifications
| Attribute | Value |
|---|---|
| Model Number | TS-1 |
| Brand | FGI |
| Product Dimensions | 7 x 4 x 4 inches |
| Item Weight | 1.2 Pounds |
| Controller Type | Push Button |
| Color | Black |
| Temperature Control Type | Cooling |
9. Warranty Information
For detailed warranty information regarding your TrolMaster TS-1 Thermostat Station, please refer to the warranty card included with your product or visit the official FGI website. Warranty terms and conditions may vary by region and purchase date.
10. Customer Support
If you require technical assistance, have questions about your product, or need to report an issue, please contact FGI customer support through their official website or the contact information provided with your product documentation. Please have your model number (TS-1) and purchase details ready when contacting support.
