1. Product Overview
The Nolan N100-5 is a state-of-the-art modular motorcycle helmet, designed for versatility and rider comfort. It features an innovative elliptical movement chin guard, allowing for a slim profile whether the chin guard is open or closed. This helmet integrates advanced safety features and user-friendly components for an optimal riding experience.
Figure 1: Nolan N100-5 Solid Modular Motorcycle Helmet in Slate Gray. This image shows the full helmet with its clear visor down, highlighting its sleek design and the Nolan logo on the side.
Key features include:
- VPS Dropdown Interior Sunscreen: Constructed from scratch-resistant Lexan, offering full UV protection.
- Dual-Action Chin Bar Opening System: Secure and easy to operate, even with gloves.
- AirBooster Ventilation System: Ensures full interior airflow for comfort.
- Ultrawide Shield: Provides increased peripheral vision.
- Clima-Comfort Inner Liner: Made of dual-density micro-perforated fabric for cooling and comfort.
- Pinlock Fog-Resistant Lens: Included for clear vision in varying conditions.
2. Safety Information
Always prioritize safety when operating a motorcycle. This helmet is designed to provide protection, but no helmet can protect against all possible impacts. Always wear appropriate protective gear.
- Ensure the helmet fits snugly and securely before every ride.
- Never modify the helmet's structure or components.
- Replace the helmet immediately after any significant impact, even if visible damage is not apparent.
- This helmet meets or exceeds D.O.T. standards for safety.
- Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
3. Components
Familiarize yourself with the main components of your Nolan N100-5 helmet:
- Outer Shell: The primary protective layer.
- Visor (Ultrawide Shield): The clear outer shield providing vision and protection.
- VPS Sunscreen: The internal tinted drop-down visor.
- Chin Guard: The movable lower section of the helmet.
- Chin Bar Opening System: Mechanism for raising and lowering the chin guard.
- AirBooster Ventilation System: Vents located on the top and front for airflow.
- Clima-Comfort Inner Liner: Removable and washable padding inside the helmet.
- Cheek Pads: Removable padding for cheek comfort and fit.
- Retention System: The chin strap with micrometric closure for securing the helmet.
- Pinlock Lens: An anti-fog insert for the main visor.
4. Setup
Before your first ride, ensure proper setup and fit.
4.1. Initial Fit Adjustment
- Place the helmet on your head. It should feel snug but not uncomfortably tight.
- The helmet should not move freely when you shake your head.
- Ensure the cheek pads provide firm, even pressure against your cheeks.
- Fasten the micrometric retention system securely under your chin. It should be tight enough that you cannot pull the helmet off your head when the chin guard is closed.
4.2. Pinlock Lens Installation (if not pre-installed)
The Pinlock lens helps prevent fogging of the main visor.
- Remove the main visor from the helmet according to the instructions in the operating section (or refer to Nolan's official video guides).
- Gently flex the main visor flat.
- Align the Pinlock lens with the pins on the inside of the main visor.
- Press the edges of the Pinlock lens onto the pins, ensuring a tight seal around the entire perimeter.
- Reinstall the main visor onto the helmet.
5. Operating Instructions
5.1. Chin Guard Operation
The N100-5 features a dual-action chin bar opening system.
- To Open: Locate the two release buttons, typically one on each side of the chin bar. Simultaneously press both buttons and lift the chin guard upwards until it locks into the open position.
- To Close: Firmly pull the chin guard downwards until it clicks securely into place. Ensure it is fully latched before riding.
5.2. VPS Sunscreen Operation
The internal VPS sunscreen can be deployed or retracted as needed.
- To Deploy: Use the lever located on the left side of the helmet to slide the sunscreen down.
- To Retract: Push the lever upwards, or use the easy access side lever for instant retraction in emergency situations.
5.3. Ventilation System (AirBooster)
Adjust the vents to control airflow within the helmet.
- Locate the top and chin vents.
- Slide the vent covers to open or close the air intakes as desired for optimal comfort.
6. Maintenance
Regular maintenance will prolong the life and effectiveness of your helmet.
6.1. Cleaning the Outer Shell
- Use a soft cloth and mild soap with lukewarm water.
- Avoid abrasive cleaners, solvents, or petroleum-based products, as these can damage the shell's finish and integrity.
- Rinse thoroughly and air dry.
6.2. Cleaning the Visor and VPS Sunscreen
- Remove the visor and Pinlock lens (if applicable).
- Clean with a soft cloth and lukewarm water. Specialized helmet visor cleaners can also be used.
- Do not use harsh chemicals.
- For the Pinlock lens, only clean with a soft, damp cloth and air dry. Do not rub vigorously.
6.3. Cleaning the Inner Liner and Cheek Pads
- The Clima-Comfort inner liner and one-piece cheek pads are designed for simple removal and replacement.
- Hand wash with mild soap and cold water.
- Allow to air dry completely before reinstalling. Do not machine wash or tumble dry.
7. Troubleshooting
This section addresses common issues you might encounter.
- Visor Fogging: Ensure the Pinlock lens is correctly installed and sealed. Adjust ventilation to increase airflow.
- Chin Guard Not Latching: Ensure no obstructions are preventing the chin guard from fully closing. Apply firm, even pressure until it clicks into place. If issues persist, inspect the latching mechanism for damage.
- Helmet Feels Too Tight/Loose: Helmet fit is crucial for safety. If the helmet feels too tight or too loose, re-evaluate the sizing. Inner liners and cheek pads are available in different thicknesses to fine-tune the fit.
- Excessive Noise: Ensure all vents are closed if noise is an issue. Check that the visor and chin guard are fully closed and sealed.
For issues not covered here, please contact Nolan customer support or an authorized dealer.
8. Specifications
| Feature | Detail |
|---|---|
| Model Name | Nolan N155270330086 |
| Brand | Nolan |
| Color | GRAY |
| Material | Thermoplastic |
| Item Weight | 5.19 pounds |
| Product Dimensions | 11 x 11 x 14 inches |
| Certificate Type | DOT |
| Shell Type | Hard |
| Closure Type | Micrometric |
| Exterior | Painted |
| Sport | Motorcycling |
9. Warranty and Support
For detailed warranty information and customer support, please refer to the official Nolan website or contact your authorized Nolan dealer. Keep your proof of purchase for any warranty claims.
Nolan provides support for their products and can assist with inquiries regarding helmet features, maintenance, and replacement parts.
