XTPTFABS 58-420 40022-91 1204-0042

Download PDF
Contents

XTPTFABS 128T Rear Drive Belt Instruction Manual

Model: 58-420 40022-91 1204-0042 | Brand: XTPTFABS

Introduction

This manual provides essential information for the installation, operation, and maintenance of your XTPTFABS 128-tooth rear drive belt. Proper installation and regular maintenance are crucial for the longevity and safe performance of your motorcycle's drive system. Please read these instructions thoroughly before proceeding with any procedures.

Product Overview

The XTPTFABS 128T Rear Drive Belt is designed for specific Harley-Davidson Sportster models, offering a reliable power transfer solution. It features a high-strength neoprene layer and a durable nylon fabric tooth surface for quiet and efficient operation, as well as abrasion and break resistance.

XTPTFABS 128T Rear Drive Belt
Figure 1: General view of the XTPTFABS 128T Rear Drive Belt.
Close-up of drive belt teeth
Figure 2: Close-up view of the high-quality nylon fabric tooth surface, designed for durability and efficient power transfer.
Side view of drive belt showing neoprene layer
Figure 3: Side view illustrating the high-strength neoprene layer, contributing to the belt's abrasion and break resistance.

Product Video

Video 1: An overview of the Rear Drive Belt 128T 1-1/8", highlighting its features and construction. This video is provided by the seller, TakemyParts.

Compatibility

This XTPTFABS rear drive belt is compatible with the following Harley-Davidson Sportster models manufactured between 1991 and 2003:

  • Harley-Davidson Sportster 883
  • Harley-Davidson Sportster 1200
  • Harley-Davidson Sportster Hugger XL
  • Harley-Davidson Sportster XLH
  • Harley-Davidson Sportster 1200C
  • Harley-Davidson Sportster 883C
  • Harley-Davidson Sportster 1200S

Always verify the part number and specifications against your motorcycle's requirements before installation.

Specifications

FeatureSpecification
BrandXTPTFABS
Manufacturer Part Number58-420 40022-91 1204-0042
Product Dimensions128"L x 1.13"W (128 x 1.13 x 0.04 inches)
Item Weight1.06 pounds
Belt StyleToothed Belt
Compatible DevicesMotorcycle

Installation (Setup)

Installation of a motorcycle drive belt requires specialized tools and mechanical knowledge. It is highly recommended that installation be performed by a qualified motorcycle mechanic.

  1. Preparation: Ensure the motorcycle is on a stable stand, and the engine is cool. Disconnect the battery.
  2. Rear Wheel Removal: Loosen the axle nut and remove the rear wheel to access the drive belt.
  3. Old Belt Removal: Carefully remove the old drive belt from the pulleys. Inspect pulleys for wear or damage.
  4. New Belt Installation: Route the new XTPTFABS drive belt around the front and rear pulleys. Ensure the belt teeth align correctly with the pulley grooves.
  5. Rear Wheel Reinstallation & Alignment: Reinstall the rear wheel. Adjust the axle to achieve proper belt tension and wheel alignment according to your motorcycle's service manual specifications. Incorrect tension can lead to premature belt wear or failure.
  6. Final Checks: Tighten all fasteners to the manufacturer's torque specifications. Reconnect the battery. Test the motorcycle at low speeds in a safe environment before full operation.

Warning: Improper installation can lead to serious injury or damage to your motorcycle. If you are unsure about any step, consult a professional mechanic.

Operation

Once installed, the drive belt operates as part of your motorcycle's power transmission system. No specific operational steps are required beyond normal motorcycle use. However, be mindful of the following:

  • Avoid sudden, harsh acceleration or braking, which can put excessive stress on the drive belt.
  • Do not overload the motorcycle beyond its recommended weight capacity.
  • Operate the motorcycle within its intended design parameters.

Maintenance

Regular inspection and maintenance will extend the life of your XTPTFABS drive belt and ensure safe operation.

  • Routine Inspection: Periodically inspect the belt for signs of wear, cracks, fraying, missing teeth, or foreign objects embedded in the belt.
  • Tension Check: Check belt tension regularly, especially after the first few hundred miles of a new installation. Adjust tension according to your motorcycle's service manual.
  • Cleaning: Keep the belt and pulleys clean from dirt, debris, oil, and grease. Use a mild soap and water solution if cleaning is necessary, and ensure it is thoroughly dry before operation.
  • Storage: If storing the motorcycle for an extended period, ensure the belt is clean and properly tensioned.
  • Replacement: Replace the drive belt if any significant damage or excessive wear is observed. Refer to your motorcycle's service manual for recommended replacement intervals.

Troubleshooting

If you experience issues with your drive belt, consider the following common problems and solutions:

  • Excessive Noise (Whining/Squealing):
    Possible Cause: Incorrect belt tension (too tight or too loose), misaligned pulleys, or foreign debris.
    Solution: Check and adjust belt tension. Inspect pulley alignment. Clean the belt and pulleys.
  • Premature Wear/Cracking:
    Possible Cause: Incorrect tension, exposure to harsh chemicals, extreme temperatures, or damaged pulleys.
    Solution: Verify tension. Avoid chemical exposure. Inspect pulleys for sharp edges or damage. Replace the belt if wear is significant.
  • Belt Slippage:
    Possible Cause: Insufficient belt tension, oil/grease contamination, or worn belt/pulleys.
    Solution: Adjust belt tension. Clean any contaminants. Inspect for wear and replace components as needed.
  • Belt Breakage:
    Possible Cause: Severe impact, extreme overload, incorrect tension, or manufacturing defect.
    Solution: Replace the belt. Investigate the cause of breakage to prevent recurrence. Professional inspection is recommended.

For persistent issues or concerns, consult a certified motorcycle mechanic.

Warranty Information

For specific warranty terms and conditions regarding your XTPTFABS 128T Rear Drive Belt, please refer to the documentation provided with your purchase or contact the seller directly. Warranty coverage typically addresses manufacturing defects but may not cover damage due to improper installation, misuse, or normal wear and tear.

Support

If you require further assistance, have questions about installation, or need to report an issue, please contact the seller or manufacturer through the platform where the product was purchased. Provide your product model number (58-420 40022-91 1204-0042) and purchase details for efficient support.

© 2023 XTPTFABS. All rights reserved. Information in this manual is subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.