Introduction
This manual provides essential instructions for the safe assembly, operation, and maintenance of your BAIDE HOME 28-inch Table Top Propane Fire Pit. Please read this manual thoroughly before use and retain it for future reference.
Important Safety Information
- For outdoor use only. Do not use indoors or in an enclosed area.
- Keep children and pets away from the fire pit.
- Maintain a safe distance from combustible materials.
- Ensure proper ventilation.
- Use only propane gas.
- Do not store a spare propane cylinder under or near the appliance.
- Always turn off the gas supply at the cylinder when not in use.
- Never leave the fire pit unattended when in operation.
- Allow the unit to cool completely before moving or storing.
- Inspect the hose before each use for signs of excessive abrasion or wear.
Package Contents
Verify that all components are present before assembly.
- Fire Pit Unit (main body)
- Wind Glass Shield
- Glass Rocks
- Stainless Steel Burner
- 8ft Gas Hose with Regulator
- Rain Cover
- AA Battery (for electronic igniter)
Setup and Assembly
- Unpack Components: Carefully remove all items from the packaging.
- Place Fire Pit: Position the fire pit on a stable, non-combustible surface. Ensure adequate clearance from overhead and side structures.
The fire pit is designed for placement on various outdoor tables, including those with or without umbrella holes. - Install Glass Rocks: Distribute the provided glass rocks evenly over the burner area. Do not overfill.
- Install Wind Glass Shield: Place the wind glass shield securely around the burner using the integrated hook design.
The glass bracket features a hook design to securely hold the glass shield in place. - Connect Propane Hose:
The regulator hose connection port is initially located at the bottom, suitable for tables with an umbrella hole.
If your table does not have an umbrella hole, you can convert the connection to a side connection:
- Remove the bottom port bracket.
- Secure it into the side hole on the back side of the unit.
Connect the 8ft gas hose to the fire pit and to a 20lb LP (Liquefied Petroleum) tank (not included). Ensure all connections are tight.
Illustration of the two setup options for the propane hose connection: bottom connection for tables with umbrella holes, and side connection for other tables. - Install AA Battery: Insert one AA battery into the electronic igniter compartment.
Operating Instructions
- Open Gas Supply: Slowly open the valve on the propane tank.
- Ignite Fire Pit: Press and hold the igniter button while slowly turning the control knob to the "LOW" position. Continue holding the igniter button until the flame is established.
- Adjust Flame: Once lit, release the igniter button and adjust the flame height using the control knob.
- To Turn Off: Turn the control knob to the "OFF" position, then close the valve on the propane tank.
Caution: If the fire does not stay lit, try partially closing the valve on the propane tank. A 1/4 turn open may be optimal.
Maintenance
- Cleaning: Allow the fire pit to cool completely. Wipe exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners.
- Storage: When not in use, especially during inclement weather or extended periods, cover the fire pit with the provided rain cover. Store the propane tank in a well-ventilated area, away from direct sunlight and heat sources.
- Inspection: Regularly inspect the gas hose and connections for leaks, cuts, or damage. Replace any damaged parts immediately.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fire pit does not ignite. | No gas flow; igniter not sparking; low battery. | Check propane tank valve; ensure hose is connected; replace AA battery. |
| Flame is weak or inconsistent. | Low gas pressure; partially closed tank valve; clogged burner. | Ensure propane tank valve is fully open (or partially open if flame doesn't stay lit); check for obstructions in burner. |
| Fire does not stay lit after releasing igniter. | Excess gas flow from tank. | Try partially closing the propane tank valve (e.g., 1/4 turn open) to reduce initial gas flow. |
| Gas odor detected. | Gas leak. | Immediately turn off gas supply. Check all connections for leaks using a soapy water solution. Do not operate if a leak is present. |
Product Specifications
- Model: 95552-AZ01
- Brand: BAIDE HOME
- Dimensions: 28"D x 7.28"W x 8.25"H
- Material: Stainless Steel, Powder Coated Steel
- Fuel Type: Liquefied Petroleum Gas (LP)
- Heat Output: 40,000 BTU
- Item Weight: 20.02 Pounds
- Ignition: Electronic
- Required Battery: 1 AA battery
- UPC: 691189955566, 691189955900
Warranty and Support
For warranty information or technical support, please contact BAIDE HOME customer service. Refer to your purchase documentation for specific contact details.