DD&HAPP B797

Download PDF
Contents

DD&HAPP 1 Gallon Double Glass Drink Dispensers

Model: B797

Product Overview

The DD&HAPP 1 Gallon Double Glass Drink Dispensers are designed for serving beverages at parties, gatherings, or for daily use. This set includes two 1-gallon glass dispensers, a sturdy metal stand, stainless steel spigots, and ice cylinders for keeping drinks chilled without excessive dilution. The included hanging chalkboards allow for easy labeling of contents.

Two 1-gallon glass drink dispensers with stainless steel spigots on a black metal stand, with two clear ice cylinders and two small chalkboards.

Image: The complete DD&HAPP 1 Gallon Double Glass Drink Dispenser set, showcasing the two glass jars, metal stand, spigots, ice cylinders, and chalkboards.

Package Contents

Please verify that all components are present and in good condition upon opening the package:

  • 2 x 1 Gallon Glass Drink Dispensers
  • 2 x Food-grade 304 Stainless Steel Spigots
  • 1 x Metal Bracket (Stand)
  • 1 x Orange Ring (Used as a wrench for spigot installation)
  • 2 x Ice Cylinders (Perforated)
  • 2 x Hanging Chalkboards with string
  • Additional seals/washers for spigot assembly
Close-up of the glass dispenser and metal stand, with text 'High quality material' and icons for food-grade, no leaks, metal shelf, easy to clean, simple installation.

Image: Components of the dispenser set, highlighting the high-quality materials used.

Setup and Assembly

Follow these steps for proper assembly to ensure leak-free operation and stability:

  1. Spigot Installation:
    • Ensure the glass dispenser is clean and dry.
    • Disassemble the spigot components: metal nut, metal washer, rubber washer, spigot body.
    • From the outside of the dispenser, insert the spigot body through the hole.
    • Place one rubber washer onto the spigot thread from the inside of the dispenser, pressing it firmly against the glass.
    • Next, place one metal washer onto the spigot thread from the inside.
    • Finally, screw the metal nut onto the spigot thread from the inside.
    • Use the provided orange ring wrench to tighten the metal nut securely. Exercise caution during this step as metal edges can be sharp. It is recommended to wear protective gloves. Do not overtighten, as this may crack the glass.
    • Repeat for the second dispenser.
    Diagram showing the assembly order of the spigot: metal nut, metal washer, rubber washer, glass, rubber washer, metal washer, spigot.

    Image: Detailed diagram for spigot installation, showing each component and its placement.

  2. Stand Assembly:
    • Place the metal stand on a flat, stable surface.
    • Ensure the stand is oriented correctly. The dips or indentations in the stand are designed to accommodate the spigots, allowing them to extend freely. If the stand appears wobbly, it may be upside down.
    • The stand features anti-skid elements (silicone tubes) on the bars where the dispensers rest. Ensure these are properly seated to prevent the dispensers from sliding.
    Close-up of the metal stand showing a clear silicone tube on one of the bars, labeled 'Antiskid'.

    Image: Detail of the anti-skid feature on the metal stand, showing the silicone tubing.

  3. Placement of Dispensers:
    • Carefully place the assembled glass dispensers onto the metal stand, aligning the spigots with the designated dips.

Setup Video Guide

Video: An official product video from DD&HAPP US demonstrating the setup and use of the 1 Gallon drink dispensers for parties. This video provides a visual guide to assembly and general operation.

Operating Instructions

Using your DD&HAPP drink dispensers is straightforward:

  1. Filling the Dispensers:
    • Remove the stainless steel lid from the top of the glass dispenser.
    • Pour your desired beverage into the dispenser.
    • If using the ice cylinder, fill it with water and freeze it, or fill it with ice cubes. Insert the filled ice cylinder into the dispenser before or after adding the beverage. Note: The ice cylinders are perforated and designed to allow some dilution for optimal chilling and flavor infusion.
    • Securely replace the lid.
    A single glass drink dispenser filled with lemon-infused water, surrounded by lemons, with icons showing various applications like fruit tea, lemon squash, iced tea, and wine.

    Image: Demonstrates the versatility of the dispenser for various beverages, including fruit-infused drinks.

  2. Dispensing Beverages:
    • Place a cup or glass under the spigot.
    • Push the spigot handle upwards to open the flow.
    • Release the handle to close the flow.
  3. Using the Hanging Chalkboards:
    • Use chalk (not included) to write the name of the beverage on the small chalkboard.
    • Hang the chalkboard from the metal stand using the attached string, positioning it in front of the corresponding dispenser for easy identification.
    A hand writing 'lemon squash' on a small chalkboard hanging from the metal stand of the drink dispenser, with another chalkboard labeled 'strawberry juice'.

    Image: Illustrates the use of the hanging chalkboards for labeling different beverages.

Care and Maintenance

Proper care will extend the life of your drink dispensers:

  • Cleaning the Glass Dispensers:
    • The glass dispensers are NOT dishwasher safe. Hand wash with warm, soapy water.
    • Use a soft brush or sponge to clean the interior.
    • Rinse thoroughly and allow to air dry completely before storage.
  • Cleaning the Spigots:
    • For thorough cleaning, the stainless steel spigots can be disassembled by unscrewing the nut from the inside of the dispenser.
    • Wash all spigot components with warm, soapy water and a small brush to remove any residue.
    • Rinse well and ensure all parts are dry before reassembling.
  • Cleaning the Metal Stand:
    • Wipe the metal stand with a damp cloth. Do not use abrasive cleaners.
    • Dry immediately to prevent rust.
  • Storage:
    • Store all components in a dry place when not in use.
    • Ensure glass dispensers are completely dry to prevent mildew or odors.

Troubleshooting

ProblemPossible CauseSolution
Spigot is leakingImproper spigot installation; washers not seated correctly or nut not tightened enough.Disassemble the spigot and reassemble carefully, ensuring rubber washers are flush against the glass on both sides and the nut is tightened securely with the orange wrench. Do not overtighten.
Stand is wobbly or unstableStand is assembled or oriented incorrectly.Ensure the stand is placed on a flat surface and that the dips in the stand are facing upwards to properly cradle the dispensers and spigots.
Ice cylinder dilutes beverage too muchThe ice cylinders are designed with perforations.This is an intended design feature to allow for chilling and flavor infusion. If less dilution is desired, use larger ice cubes directly in the beverage or pre-chill the beverage before adding to the dispenser.
Difficulty cleaning inside dispenserNarrow opening.Use a long-handled bottle brush or a sponge attached to a handle for effective cleaning.

Specifications

  • Brand: DD&HAPP
  • Model Number: B797
  • Material: Glass (Dispensers), 304 Stainless Steel (Spigots), Metal (Stand)
  • Color: Clear
  • Capacity: 1 Gallon per dispenser (2 Gallons total)
  • Product Dimensions (each dispenser): 5.9"L x 5.9"W x 9.8"H
  • Item Weight (total): Approximately 8.82 pounds (4.01 Kilograms)
  • Dishwasher Safe: No (Hand wash only)
  • UPC: 797447660873
  • Country of Origin: China

Warranty and Support

DD&HAPP is committed to customer satisfaction. If you encounter any problems with your product, please contact DD&HAPP US directly. They aim to help solve all problems within 24 hours.

For support, please refer to the contact information provided with your purchase or visit the official DD&HAPP website.

© 2025 DD&HAPP. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.