1. Important Safety Instructions
Please read and understand all instructions before assembling and using this product. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Electrical Safety: Always unplug the lamp from the power outlet before cleaning, changing the bulb, or performing any maintenance. Do not use with a damaged cord or plug.
- Indoor Use Only: This lamp is designed for indoor use in dry locations. Do not expose to water or moisture.
- Bulb Compatibility: Use only E26 base bulbs with a maximum wattage of 60W. The included LED bulb is 9W.
- Stability: Ensure the tripod base is fully extended and stable on a flat surface to prevent tipping.
- Children and Pets: Keep the lamp out of reach of small children and pets to prevent accidental tipping or damage.
2. Package Contents
Carefully unpack all components and check against the list below. If any parts are missing or damaged, please contact customer support.
- Tripod Lamp Base (Walnut Wood)
- Lampshade (Beige Linen Texture)
- Round Wooden Shelf
- 9W LED Bulb (E26 Base)
- Remote Control
- Foot Switch (integrated into power cord)
- Assembly Hardware (pre-attached or minimal)
- Instruction Manual
Image: Key components including the E26 bulb base, the round wooden shelf, and the cord management strap.
3. Setup and Assembly
Assembly of the OUTON Wood Tripod Floor Lamp is designed to be straightforward and typically takes less than 15 minutes without the need for additional tools.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface.
- Assemble Tripod Base: Extend the wooden tripod legs. Ensure they are securely locked into position, forming a stable base.
- Attach Shelf: Slide the round wooden shelf onto the central pole of the tripod. Secure it in place according to the provided mechanism (usually by twisting or tightening a nut).
- Install Lampshade: Assemble the lampshade by attaching the fabric to the metal rings. Tip: Read the lampshade instructions carefully. If the bottom piece is installed upside down, it may be difficult to correct without damaging the clips.
- Attach Lampshade to Lamp: Secure the assembled lampshade to the lamp's bulb holder.
- Insert Bulb: Screw the provided 9W LED bulb into the E26 bulb base.
- Cable Management: Use the integrated cord neater to secure the power cord along one of the tripod legs for a tidy appearance and to prevent tripping hazards.
- Placement: Position the lamp on a flat, stable surface.
Image: Visual guide demonstrating the tool-free assembly process.
Image: Detail of the cord management feature on the lamp's leg.
4. Operating Instructions
The OUTON Wood Tripod Floor Lamp offers versatile lighting options controlled by a remote or foot switch.
4.1 Power On/Off
- Foot Switch: Press the foot switch located on the power cord to turn the lamp on or off.
- Remote Control: Press the power button (⏻) on the remote control to turn the lamp on or off.
4.2 Adjusting Brightness (Dimmable Function)
The lamp is fully dimmable from 5% to 100% brightness.
- Remote Control: Use the brightness adjustment buttons (+ / -) on the remote to increase or decrease the light intensity.
4.3 Changing Color Temperature
The included LED bulb offers four color temperature settings: Warm, Warm White, Cool White, and Daylight.
- Remote Control: Use the 'K' button or dedicated color temperature buttons (if available) on the remote to cycle through the different color temperatures.
4.4 Memory Function
The lamp features a memory function that recalls your last brightness and color temperature setting when turned back on, eliminating the need to re-adjust each time.
4.5 1-Hour Timer Mode
Activate the 1-hour timer to automatically turn off the lamp after one hour.
- Remote Control: Press the timer button (1H) on the remote control to activate the 1-hour timer.
4.6 Remote Control Pairing (if needed)
If the remote control does not respond, it may need to be re-paired with the lamp:
- Ensure the lamp is plugged in and turned on.
- Unplug the lamp from the power outlet.
- Wait approximately 5 seconds.
- Plug the lamp back into the power outlet while simultaneously holding down the power button (⏻) on the remote control.
- Release the power button once the lamp responds to the remote.
Image: Remote control in use, demonstrating various light settings.
Image: Depiction of both remote control and foot switch operation.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your lamp.
- Cleaning: Always unplug the lamp before cleaning. Use a soft, dry cloth to wipe down the wooden base and lampshade. Do not use abrasive cleaners or solvents.
- Bulb Replacement: Ensure the lamp is unplugged and the bulb has cooled before attempting to replace it. Use only E26 base LED bulbs.
- Cord Inspection: Periodically check the power cord and plug for any signs of damage. If damaged, discontinue use and contact customer support.
6. Troubleshooting
If you encounter issues with your OUTON Wood Tripod Floor Lamp, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on | Not plugged in; power outlet issue; bulb loose or faulty; foot switch malfunction. | Ensure plug is fully inserted. Test outlet with another device. Tighten or replace bulb. Try using the remote control. |
| Remote control not working | Remote batteries dead; remote not paired; obstruction. | Replace remote batteries. Re-pair the remote (see Section 4.6). Ensure no objects block the signal path. |
| Light flickers or dims unexpectedly | Loose bulb; unstable power supply; faulty bulb. | Tighten bulb. Check power connection. Replace bulb. |
| Lampshade appears uneven or damaged | Incorrect assembly of lampshade frame. | Disassemble and reassemble the lampshade carefully, ensuring all clips are correctly aligned and secured. |
If the problem persists after attempting these solutions, please contact OUTON customer support for further assistance.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | H-SJJ01 |
| Brand | OUTON |
| Product Dimensions | 10"D x 10"W x 65"H (25.4 cm D x 25.4 cm W x 165.1 cm H) |
| Item Weight | 6.6 pounds (3 Kilograms) |
| Material | Wood (Rubberwood), Linen |
| Finish Type | Oil Rubbed |
| Light Source Type | LED |
| Bulb Base | E26 |
| Wattage | 9 Watts (Max 60 Watts compatible) |
| Brightness | 810 Lumens |
| Color Temperature | Adjustable (Warm, Warm White, Cool White, Daylight) |
| Control Method | Remote Control, Foot Switch |
| Special Features | Dimmable, 1-Hour Timer, Memory Function, Integrated Shelf |
| Power Source | Corded Electric |
| Indoor/Outdoor Usage | Indoor Use Only |
8. Warranty and Support
OUTON is committed to providing high-quality products and customer satisfaction. This product comes with a 2-year support period.
If you encounter any issues or have questions regarding your OUTON Wood Tripod Floor Lamp, please do not hesitate to contact our customer service team. We aim to provide quick and friendly service to resolve any concerns.
For support, please visit the official OUTON store or contact us through your purchase platform. You can find more information and contact details on the OUTON Brand Store.
