Introduction
This manual provides essential instructions for the proper installation, maintenance, and troubleshooting of your ALLIANCE LAUNDRY SYSTEMS Plastic Drain Hose, Model 685730. Please read this manual thoroughly before installation and retain it for future reference.
Product Overview
The ALLIANCE LAUNDRY SYSTEMS Plastic Drain Hose (Model 685730) is a genuine OEM replacement part designed for various laundry appliances. It is constructed from durable plastic to ensure effective water drainage from your washing machine or all-in-one washer/dryer unit.
Figure 1: The ALLIANCE LAUNDRY SYSTEMS Plastic Drain Hose, Model 685730. This image shows the white corrugated plastic hose coiled, with a slightly wider, smooth end for connection.
This drain hose is compatible with laundry appliances from brands such as Speed Queen, Ipso, Cissell, Unimac, and Huebsch, in addition to other Alliance Laundry Systems models.
Setup and Installation
- Safety First: Before beginning installation, ensure your laundry appliance is disconnected from the power supply and water source.
- Remove Old Hose: Carefully detach the existing drain hose from both the appliance and the drain standpipe or utility sink. Be prepared for residual water to drain out.
- Connect to Appliance: Securely attach one end of the new ALLIANCE LAUNDRY SYSTEMS drain hose to the drain outlet on your washing machine. Ensure the connection is tight to prevent leaks. Depending on your appliance, a hose clamp (not included) may be required.
- Position Drain End: Route the other end of the drain hose into a standpipe, utility sink, or other approved drainage system. Ensure the hose is positioned to prevent siphoning and is securely held in place to avoid dislodging during operation.
- Check for Kinks: Verify that the hose is not kinked or bent sharply, as this can impede drainage and cause appliance malfunction.
- Restore Connections: Once the hose is securely installed, reconnect the appliance to the water supply and power.
Operating Considerations
While the drain hose itself does not have active "operation," proper function is critical for your laundry appliance. After installation, perform a test cycle to ensure:
- There are no leaks at the connection points.
- Water drains freely and completely from the appliance.
- The hose remains securely in its drainage position throughout the cycle.
Regularly inspect the hose for any signs of wear or damage that could lead to leaks or blockages.
Maintenance
To ensure the longevity and proper function of your drain hose, consider the following maintenance tips:
- Regular Inspection: Periodically check the entire length of the hose for cracks, punctures, or signs of wear. Pay close attention to the connection points.
- Cleanliness: If you notice slow drainage or suspect a blockage, disconnect the hose and inspect the interior for lint, debris, or detergent residue. Clean with warm, soapy water and a long brush if necessary.
- Prevent Kinks: Ensure the hose is not consistently bent or kinked, as this can weaken the material over time and lead to leaks.
- Avoid Harsh Chemicals: Do not use strong chemical cleaners on or inside the hose, as these can degrade the plastic material.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water Leakage | Loose connection at appliance or drain point; damaged hose. | Tighten connections. Inspect hose for damage; replace if necessary. Ensure hose clamps are secure. |
| Slow or No Drainage | Hose is kinked or blocked; drain standpipe is clogged. | Straighten any kinks. Disconnect and clear any blockages in the hose. Check and clear the drain standpipe. |
| Hose Dislodges from Drain | Hose not securely fastened; excessive vibration from appliance. | Ensure the hose is properly inserted into the drain and secured with a U-bend or strap if needed. Check appliance leveling to reduce vibration. |
Specifications
- Part Number: 685730
- Material: Plastic
- Item Weight: Approximately 12.8 ounces
- Package Dimensions: Approximately 20.9 x 14.45 x 4.15 inches
- Compatibility: Fits Speed Queen, Ipso, Cissell, Unimac, Huebsch, and Alliance Laundry Systems Washer/Dryer models.
Warranty Information
Specific warranty details for the ALLIANCE LAUNDRY SYSTEMS Plastic Drain Hose (Model 685730) are typically provided by the original seller or manufacturer at the time of purchase. Please refer to your purchase documentation or contact the seller directly for information regarding warranty coverage and terms.
Support
For further assistance, technical support, or to inquire about replacement parts, please contact ALLIANCE LAUNDRY SYSTEMS or your authorized dealer. When contacting support, please have your product model number (685730) and purchase details readily available.
You may also visit the official ALLIANCE LAUNDRY SYSTEMS website for additional resources and contact information.
