OlarHike Single Air Bed Instruction Manual

Introduction

This manual provides essential instructions for the safe and efficient use, setup, maintenance, and storage of your OlarHike Single Air Bed, Model AMH5V138. Please read this manual thoroughly before first use and retain it for future reference.

Safety Information

• Do not use the air bed near open flames, heaters, or other heat sources.
• Keep sharp objects away from the air bed to prevent punctures.
• Ensure the area around the air bed is clear of obstructions.
• Do not overinflate the air bed. Overinflation can cause damage.
• This product is not a toy. Keep children supervised when near the air bed.
• Maximum weight capacity: 299 kg (660 lbs). Do not exceed this limit.
• Always use the electric pump with the correct voltage (220-240V as indicated on the product).
• Avoid prolonged exposure to direct sunlight, which can damage the material.

Package Contents

Verify that all items are present in the package:

• 1 x OlarHike Single Air Bed with Built-in Pump
• 1 x User Manual (this document)
• 4 x Repair Patches
• 1 x Carrying Bag

Setup and Inflation

Your OlarHike Air Bed features a built-in electric pump for quick inflation. It also includes a manual valve for inflation or deflation without electricity.

Electric Inflation (220-240V)

1. Unroll the air bed on a clean, flat surface, free from sharp objects.
2. Locate the built-in electric pump on the side of the air bed.
3. Open the pump compartment cover.
4. Plug the power cord into a standard 220-240V wall outlet.
5. Turn the pump dial to the "Inflate" position. The air bed will begin to inflate.
6. Inflate until the bed is firm to the touch (approximately 2-5 minutes). Do not overinflate.
7. Turn the pump dial to the "Off" position and unplug the power cord.
8. Store the power cord neatly back into its compartment and close the cover securely.

Manual Inflation

In situations where electricity is unavailable, the air bed can be inflated using an external manual or battery-operated pump (not included).

1. Locate the 2-in-1 manual valve on the air bed.
2. Open the larger cap of the valve.
3. Insert the nozzle of your external pump into the valve opening.
4. Inflate the air bed to your desired firmness.
5. Remove the pump nozzle and quickly close the larger cap to prevent air loss.

Operation and Usage

Once inflated, the OlarHike Single Air Bed is ready for use. For optimal comfort and longevity, consider the following:

• Initial Stretch: New PVC material may stretch during the first few uses, causing the bed to feel softer. This is normal. A quick 1-minute top-up inflation after the first one or two nights of use is recommended to maintain desired firmness.
• Daily Use: If using the air bed daily, a brief top-up inflation (approximately 1 minute) may be necessary to ensure consistent comfort and support.
• Protection: Although the top surface is soft and durable, covering the air bed with a blanket or sheet is recommended for enhanced comfort and protection against wear.
• Weight Distribution: Distribute weight evenly across the surface of the air bed.

Deflation and Storage

Proper deflation and storage will extend the life of your air bed.

Electric Deflation

1. Ensure the air bed is clean and dry.
2. Open the pump compartment cover and plug the power cord into a 220-240V wall outlet.
3. Turn the pump dial to the "Deflate" position. The pump will actively remove air from the bed.
4. Allow the pump to run until most of the air has been removed and the bed is flat.
5. Turn the pump dial to "Off" and unplug the cord.
6. Store the power cord and close the compartment cover.

Manual Deflation

To manually deflate or remove remaining air after electric deflation:

1. Locate the 2-in-1 manual valve.
2. Open the larger cap of the valve.
3. Gently roll or press the air bed to expel the remaining air.
4. Once deflated, close the valve cap securely.

Storage

1. Ensure the air bed is completely deflated and dry before folding.
2. Fold the air bed neatly to fit into the provided carrying bag.
3. Store the air bed in a cool, dry place, away from direct sunlight and extreme temperatures.

Maintenance

• Cleaning: To clean the air bed, wipe it with a damp cloth and mild soap. Do not use harsh chemicals or abrasive cleaners. Ensure the bed is completely dry before storage.
• Repair Patches: In case of a small puncture, use the provided repair patches. Clean the damaged area, apply the patch firmly, and allow it to cure for several hours before reinflating.
• Regular Inspection: Periodically inspect the air bed for any signs of wear, damage, or leaks.

Troubleshooting

Specifications

Warranty and Support

For warranty information or customer support, please refer to the contact details provided with your purchase documentation or visit the official OlarHike website. Keep your purchase receipt as proof of purchase.