Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your LEONLITE 3CCT LED Motion Sensor Security Flood Light, Model 19032. Please read this manual thoroughly before installation and retain it for future reference.
Safety Information
- Electrical Safety: Always turn off power at the circuit breaker before installing or servicing the fixture. Ensure all wiring connections are secure and comply with local electrical codes. If you are unsure about wiring, consult a qualified electrician.
- Grounding: This fixture must be properly grounded to prevent potential electrical shock.
- Operating Voltage: This product is designed for 120V AC power supply.
- Environmental Rating: The fixture is IP65 rated, indicating protection against dust and water jets. It is suitable for wet locations.
- Certifications: This product is ETL and FCC certified, ensuring compliance with safety and performance standards.
Package Contents
Verify that all components are present before beginning installation:
- LEONLITE 3CCT LED Motion Sensor Security Flood Light (1 unit)
- Mounting Plate (1 unit)
- Mounting Screws and Anchors (set)
- Wire Nuts (set)
- Gasket (1 unit)
- Instruction Manual (this document)
Figure 1: Technical drawing showing the product dimensions and a display of included mounting accessories such as the mounting plate, screws, and wire nuts.
Product Features
- Selectable Color Temperature (3CCT): Choose between 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight) to suit your preference.
- High Brightness: Delivers 3000 lumens of illumination.
- Motion Sensor: 180° detection angle with a range of up to 59 feet (18 meters).
- Adjustable Design: Two lamp heads rotate 180°, and the motion sensor rotates 360° for optimal coverage.
- Durable Construction: Features a sturdy aluminum body for efficient heat dissipation and resistance to weather conditions.
- Multiple Operating Modes: On-Time, Auto (motion detection), and Dusk-to-Dawn modes.
Figure 2: Front view of the LEONLITE 3CCT LED Motion Sensor Security Flood Light, showcasing its two adjustable light heads and integrated motion sensor.
Figure 3: Illustration highlighting the adjustable features: 180° rotation for light heads, 360° rotation for the motion sensor, and durable aluminum housing with integrated LED chips.
Setup and Installation
- Prepare for Installation: Turn off power at the circuit breaker. Ensure the mounting surface is stable and can support the fixture.
- Mounting Plate Installation: Secure the mounting plate to the junction box using the provided screws. Ensure the plate is flush against the surface.
- Wiring: Connect the fixture's wires to your household wiring. Connect the black wire (Live) to the black wire, the white wire (Neutral) to the white wire, and the green/ground wire to the ground wire. Use the included wire nuts to secure connections.
- Fixture Attachment: Carefully align the fixture with the mounting plate and secure it with the central screw. Ensure the gasket is properly seated to maintain the IP65 rating.
- Adjust Light Heads and Sensor: Loosen the adjustment screws on the light heads and motion sensor to position them as desired. Tighten the screws once adjusted.
Figure 4: Image illustrating the CCT toggle switch for selecting 3000K, 4000K, or 5000K color temperatures. This switch is located on the fixture body and should be set before final installation or with power off.
Operating Instructions
The flood light offers three operational modes and adjustable settings for customization.
Mode Selection
Use the switch on the bottom of the motion sensor to select one of the following modes:
- On-Time Mode: The light functions as a standard lamp, controlled by a wall switch. Motion sensing is disabled.
- Auto Mode (Motion Detection): The light automatically turns on when motion is detected at night and turns off after a set delay. The Lux and Time knobs control its behavior.
- Dusk-to-Dawn Mode (D2D): The built-in photocell automatically turns the light on at dusk and off at dawn. Motion sensing is disabled in this mode.
Figure 5: Diagram showing the three operational modes: On-Time, Motion Detection, and Dusk-to-Dawn.
Adjustable Settings (Auto Mode Only)
Three knobs allow fine-tuning of the motion sensor's performance:
- Lux Knob: Adjusts the ambient light level at which the motion sensor becomes active. Rotate clockwise for higher sensitivity (activates in brighter conditions), counter-clockwise for lower sensitivity (activates only in darker conditions).
- Time Knob: Sets the duration the light remains on after motion is detected. Rotate clockwise for a longer delay (up to 5 minutes), counter-clockwise for a shorter delay (minimum 5 seconds).
- Range Knob: Controls the motion detection distance. Rotate clockwise for a wider detection range (up to 59 feet), counter-clockwise for a shorter range.
Figure 6: Close-up of the control panel with three adjustable knobs: Lux, Time, and Range, along with the mode selection switch.
Figure 7: An outdoor scene demonstrating the 180° detection angle and 59ft (18m) detection distance of the motion sensor.
Maintenance
Regular maintenance ensures optimal performance and longevity of your security light.
- Cleaning: Periodically clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or electrical components.
- Inspection: Annually inspect the fixture for any signs of damage, loose wiring, or wear. Ensure all seals and gaskets are intact to maintain water resistance.
- LED Longevity: The integrated LED chips have a long lifespan (50,000 hours) and do not require replacement.
Troubleshooting
If your security light is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Incorrect wiring. Lux setting too low (in Auto mode). | Check circuit breaker. Verify wiring connections. Adjust Lux knob clockwise. |
| Light stays on continuously. | Fixture is in On-Time or D2D mode. Continuous motion detected. Time setting too long. | Switch to Auto mode. Ensure no constant motion in detection area. Adjust Time knob counter-clockwise. |
| Light flickers or cycles on/off rapidly. | Interference with motion sensor. Lux setting too sensitive. | Ensure no objects (e.g., tree branches) are moving in the sensor's field of view. Adjust Lux knob counter-clockwise to reduce sensitivity. |
| Motion sensor not detecting. | Range setting too low. Obstruction in detection path. Sensor positioned incorrectly. | Adjust Range knob clockwise. Clear obstructions. Reposition sensor for optimal coverage. |
Specifications
| Specification | Detail |
|---|---|
| Brand | LEONLITE |
| Model Number | 19032 |
| Color | White |
| Material | Aluminum |
| Light Source Type | LED |
| Wattage | 25 watts |
| Voltage | 120 Volts (AC) |
| Brightness | 3000 Lumens |
| Color Temperature | 3000K/4000K/5000K Selectable |
| Motion Detection Angle | 180° |
| Motion Detection Distance | Up to 59 feet (18 meters) |
| Water Resistance Level | IP65 (Waterproof) |
| Product Dimensions | 8.07"L x 7.48"W x 5.9"H |
| Item Weight | 2.4 Pounds |
| Lifespan | 50,000 hours |
| Certifications | ETL, FCC |
Warranty and Support
This LEONLITE security light comes with a 3-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For warranty claims or technical support, please contact LEONLITE customer service through the retailer where the product was purchased or visit the official LEONLITE website for contact information.
