1. Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Cecotec Bolero Flux Ire 388000 Island Extractor Hood. Please read this manual thoroughly before use and keep it for future reference.
Key Features:
- Round island extractor hood with a diameter of 38 cm.
- Stainless steel finish for durability and aesthetic appeal.
- High suction power of 800 m³/h with a 210W motor.
- Energy efficiency class A++.
- Electronic control with 3 power levels.
- Equipped with a Ø176 carbon filter for odor removal.
- 5-layer aluminum grease filter for effective grease and smoke capture.
- Integrated LED lighting for enhanced visibility.
- Delay function for automatic shutdown.
2. Safety Instructions
Always adhere to the following safety precautions to prevent injury or damage to the appliance.
- Ensure the power supply voltage matches the rating label on the hood.
- Do not allow children to operate the appliance.
- Regularly clean the grease filters to prevent fire hazards.
- Do not flambé under the range hood.
- Ensure adequate ventilation in the room when the range hood is used simultaneously with gas or other fuel-burning appliances.
- Disconnect the appliance from the main power supply before any cleaning or maintenance.
- Installation must be carried out by a qualified person in accordance with local regulations.
- The exhaust air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
3. Package Contents
Verify that all components are present and undamaged upon unpacking.
- Cecotec Bolero Flux Ire 388000 Extractor Hood Unit
- Installation Kit
- User Manual (this document)
- 2 x Carbon Filters (Ø176)
Important Note: Some users have reported receiving incomplete packages. Please ensure you have all necessary parts for installation, including the main hood unit and any separate anchoring or mounting components. Contact customer support immediately if any parts are missing.
4. Setup and Installation
This island extractor hood requires ceiling mounting. Professional installation is recommended.
4.1. Pre-Installation Checklist
- Ensure the ceiling structure can support the weight of the hood.
- Verify the distance between the cooking surface and the hood is within recommended guidelines (typically 65-75 cm for electric hobs, 70-80 cm for gas hobs).
- Confirm electrical supply is available at the installation point.
- Unpack all components and check for damage or missing parts.
4.2. Mounting the Hood
The hood is designed for island mounting. The maximum extension is 126 cm from the ceiling.
Image: Front view of the Cecotec Bolero Flux Ire 388000 island extractor hood.
Image: Side view with dimensions, indicating a maximum height of 126 cm and a 38 cm width.
Follow the detailed instructions provided in the installation kit for securing the hood to the ceiling. Ensure all connections are tight and secure.
4.3. Electrical Connection
Connect the hood to a grounded electrical outlet. The hood operates on 220 Volts. All electrical work should be performed by a qualified electrician.
5. Operating Instructions
The Cecotec Bolero Flux Ire 388000 features electronic controls for easy operation.
Image: Electronic control panel with illuminated buttons.
5.1. Power On/Off
Press the power button to turn the hood on or off. The LED lighting will also activate with the hood.
5.2. Adjusting Suction Power
The hood offers 3 power levels and a booster function for intense suction.
- Level 1: For light cooking and simmering.
- Level 2: For general cooking.
- Level 3: For heavy cooking with significant smoke and odors.
- Booster: Provides maximum suction for a short period to clear strong fumes quickly.
Image: Visual representation of the 3 suction power levels.
5.3. LED Lighting
The integrated LED lighting provides clear illumination of your cooking area. It can be controlled independently or will turn on automatically with the hood.
Image: LED lighting illuminating the cooking surface.
5.4. Delay Function
Activate the delay function to allow the hood to continue operating for a set period after cooking, ensuring all residual fumes and odors are cleared before automatic shutdown.
6. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your extractor hood.
6.1. Cleaning the Exterior
Clean the stainless steel exterior with a soft cloth and a non-abrasive cleaner. Avoid harsh chemicals or abrasive pads that could scratch the surface.
6.2. Cleaning/Replacing Grease Filters
The 5-layer aluminum grease filters should be cleaned regularly (e.g., monthly, depending on usage) to maintain suction efficiency. They can be washed by hand with hot soapy water or in a dishwasher.
Image: Illustration of the 5-layer aluminum grease filter system.
6.3. Replacing Carbon Filters
The Ø176 carbon filters are essential for removing odors in recirculating mode. These filters cannot be washed and must be replaced periodically (typically every 3-6 months, depending on usage). Refer to the installation kit for instructions on accessing and replacing the carbon filters.
Image: Carbon filters for odor elimination.
7. Troubleshooting
If you encounter issues with your extractor hood, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not turn on. | No power supply; loose connection; faulty switch. | Check power outlet and circuit breaker. Ensure all connections are secure. Contact a qualified technician if the issue persists. |
| Low suction power. | Clogged grease filters; saturated carbon filters; improper installation. | Clean or replace grease filters. Replace carbon filters. Verify correct installation and ducting (if applicable). |
| Excessive noise. | Loose parts; motor issue; improper installation. | Check for any loose components. Ensure the hood is securely mounted. If noise persists, contact customer support. |
| Odors not removed. | Saturated carbon filters; hood not running long enough. | Replace carbon filters. Use the delay function to run the hood longer after cooking. |
| Missing installation parts. | Incomplete package delivery. | Immediately contact Cecotec customer support or your retailer with proof of purchase to request missing components. |
8. Specifications
Detailed technical specifications for the Cecotec Bolero Flux Ire 388000 Island Extractor Hood.
| Feature | Specification |
|---|---|
| Model Info | 02903 |
| Air Flow Capacity | 800 m³/h (800 CMPH) |
| Motor Power | 210 W |
| Wattage | 217 watts |
| Voltage | 220 Volts |
| Energy Efficiency Class | A++ (A+++ to D scale) |
| Annual Energy Consumption | 40.1 Kilowatt Hours Per Year |
| Noise Level | 66 dB |
| Material | Stainless Steel |
| Finish Type | Polished |
| Color | Stainless Steel |
| Mounting Type | Island Mount |
| Product Dimensions (L x W x H) | 10D x 10W x 10H millimeters (Note: Product description states 38cm diameter) |
| Item Weight | 1 Kilograms |
| Control Type | Button (Electronic Control) |
| Light Source Type | LED |
| Filter Type | Baffle (Aluminum Grease Filter) |
| Ventilation Type | Ductless/Recirculating |
| Included Components | Extractor hood, installation kit, user manual, 2 carbon filters Ø176 |
| Special Features | Noise Reduction |
Note: The product dimensions listed as 10x10x10 mm and 1kg weight in specifications appear to be placeholder values. The product description indicates a 38 cm diameter and the images show a substantial appliance. Please refer to the product packaging or manufacturer's official website for precise dimensions and weight.
9. Warranty and Support
Cecotec provides support for its products. For warranty claims or technical assistance, please contact Cecotec customer service directly.
- EU Spare Part Availability Duration: 10 Years.
- Refer to your purchase documentation for specific warranty terms and conditions.
- For support, visit the official Cecotec website or contact their customer service line.
