1. Introduction
This manual provides essential instructions for the safe and efficient operation, maintenance, and troubleshooting of your AURA Livac 114R Suction Machine. Please read this manual thoroughly before using the appliance and retain it for future reference.
The AURA Livac 114R is a versatile cleaning appliance designed for dust and water suction, carpet washing, and blower functions, offering powerful cleaning capabilities for various household and commercial needs.
2. Safety Instructions
WARNING: To reduce the risk of fire, electric shock, or injury, read and follow all instructions carefully.
- Always disconnect the power cord from the electrical outlet before servicing.
- Do not use the appliance on wet surfaces when operating in dry mode.
- Do not pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
- Use only as described in this manual. Use only manufacturer's recommended attachments.
- Do not use with a damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
- Turn off all controls before unplugging.
3. Product Components
The AURA Livac 114R Suction Machine includes the following main components:
- Main Unit (Motor housing, dust/water container)
- Flexible Hose
- Extension Wands
- Carpet Washing Nozzle
- Dust Filter
- Water Tank (for carpet washing solution)
- Power Cord
Figure 1: Overview of the AURA Livac 114R Suction Machine, showing the main unit, flexible hose, and carpet washing nozzle attachment.
4. Setup and Assembly
4.1 Unpacking
Carefully remove all components from the packaging. Check for any damage during transit. Ensure all parts listed in Section 3 are present.
4.2 Attaching the Flexible Hose
- Locate the suction inlet on the main unit.
- Insert the flexible hose connector firmly into the inlet until it clicks into place.
4.3 Attaching Extension Wands and Nozzles
- Connect the desired number of extension wands to the end of the flexible hose.
- Attach the appropriate nozzle (e.g., carpet washing nozzle, crevice tool, brush) to the end of the extension wand.
4.4 Preparing for Carpet Washing
- Open the extra basin (3.5 L capacity) for the cleaning solution.
- Fill the basin with water and a suitable carpet cleaning solution according to the solution manufacturer's instructions. Do not overfill.
- Ensure the pump connection is secure.
5. Operating Instructions
5.1 Dry Vacuuming (Dust Suction)
- Ensure the dust filter is correctly installed in the 5 L dust container.
- Connect the flexible hose and appropriate dry vacuuming nozzle.
- Plug the power cord into a 220-240V AC, 50/60Hz electrical outlet.
- Press the power button (usually green or marked with 'I') to start the motor.
- Move the nozzle over the surface to be cleaned.
- After use, press the power button to turn off the machine and unplug it.
5.2 Wet Vacuuming (Water Suction)
CAUTION: Remove the dust filter before wet vacuuming to prevent damage.
- Remove the dust filter.
- Ensure the 6 L waste basin is empty and properly secured.
- Connect the flexible hose and a suitable wet vacuuming nozzle.
- Plug the power cord into a 220-240V AC, 50/60Hz electrical outlet.
- Press the power button to start the motor.
- Vacuum up spilled liquids. Do not exceed the maximum fill line of the waste basin.
- After use, press the power button to turn off the machine and unplug it. Empty and clean the waste basin immediately.
5.3 Carpet Washing Function
- Prepare the cleaning solution in the 3.5 L extra basin as described in Section 4.4.
- Attach the carpet washing nozzle and ensure the spray hose is connected.
- Plug the power cord into a 220-240V AC, 50/60Hz electrical outlet.
- Press the main power button (for suction) and the pump power button (for spraying solution).
- Spray the cleaning solution onto the carpet by pressing the trigger on the nozzle.
- Immediately move the nozzle over the wet area to suction up the dirty solution.
- Work in small sections, overlapping slightly.
- After cleaning, run the machine with clean water to rinse the internal hoses and nozzle.
- Turn off both power buttons and unplug the machine. Empty and clean all basins.
5.4 Blower Function
- Locate the blower outlet on the main unit (usually opposite the suction inlet).
- Attach the flexible hose to the blower outlet.
- Plug the power cord into a 220-240V AC, 50/60Hz electrical outlet.
- Press the power button to activate the blower.
- Direct the airflow as needed for blowing dust or drying surfaces.
- After use, press the power button to turn off the machine and unplug it.
6. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your AURA Livac 114R.
6.1 Emptying and Cleaning the Dust/Waste Basin
- After each use, especially wet vacuuming or carpet washing, empty the 6 L waste basin.
- Rinse the basin thoroughly with clean water and allow it to air dry completely before reassembling.
6.2 Cleaning the Dust Filter
- For dry vacuuming, regularly check and clean the dust filter.
- Tap the filter gently to dislodge dust, or rinse with water if heavily soiled. Ensure it is completely dry before reinstallation.
- Replace the filter if it is damaged or excessively worn.
6.3 Cleaning the Extra Basin (Solution Tank)
- After carpet washing, empty any remaining cleaning solution.
- Rinse the 3.5 L extra basin with clean water to prevent residue buildup.
6.4 Cleaning Hoses and Nozzles
- Rinse all hoses and nozzles with clean water after wet use to prevent blockages and odors.
- Ensure they are dry before storage.
6.5 Storage
Store the appliance and its accessories in a clean, dry place, away from direct sunlight and extreme temperatures.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not turn on. | No power supply. Power cord damaged. | Check if the plug is securely inserted into the outlet. Check the circuit breaker. Do not use if cord is damaged; contact service. |
| Low suction power. | Dust/waste basin full. Filter clogged. Hose or nozzle blocked. Loose connections. | Empty the dust/waste basin. Clean or replace the filter. Check and clear any blockages in the hose or nozzle. Ensure all connections are secure. |
| Water leaks from machine. | Waste basin not properly sealed. Overfilled waste basin. Damaged seals. | Ensure the waste basin is correctly closed and sealed. Do not exceed the maximum fill line. Contact service for seal replacement. |
| Pump not spraying solution. | Solution tank empty. Pump not activated. Spray nozzle clogged. | Refill the solution tank. Ensure the pump power button is pressed. Clean the spray nozzle. |
8. Specifications
- Model: Livac 114R
- Brand: AURA
- Max. Motor Power: 2000 W
- Suction Power: 1950 mmH2O
- Voltage: 220 – 240 V AC
- Frequency: 50/60 Hz
- Air Flow: 200 m³/h
- Suction Capacity: 1.5 L/s
- Pump Power: 26 W
- Pump Pressure: 2.5 bar
- Waste Basin Volume: 6 L
- Dust Container Capacity: 5 L
- Extra Basin Volume (Solution Tank): 3.5 L
- Item Weight: 8 kg (Package Dimensions: 54 x 50.7 x 44.7 cm; 8 kg)
- Special Features: Dry, Wet, Carpet Washing, Blower Function
9. Warranty and Support
For warranty information and customer support, please refer to the warranty card included with your product or visit the official AURA website. Keep your purchase receipt as proof of purchase.
For technical assistance or spare parts, contact AURA customer service through the details provided in your product documentation.
