1. Introduction
Thank you for choosing the HOMCOM B31-319V80 3-Light Modern Floor Lamp. This manual provides essential information for the safe assembly, operation, and maintenance of your new floor lamp. Please read these instructions carefully before use and retain them for future reference.
This floor lamp features a sleek, modern design with a slim pole and three globe lampshades, providing bright illumination for various indoor spaces such as living rooms, bedrooms, or offices. It includes an on/off foot switch for convenient operation and a long power cable for flexible placement.
2. Safety Information
- Ensure the power supply is disconnected before assembly, cleaning, or bulb replacement.
- This product is intended for indoor use only. Do not expose to moisture or extreme temperatures.
- Use only E26 base bulbs with a maximum wattage of 40W per bulb.
- Do not use bulbs that exceed the specified wattage to prevent overheating and potential fire hazards.
- Keep the lamp away from flammable materials.
- Ensure all connections are secure before plugging in the lamp.
- If the power cord is damaged, it must be replaced by a qualified electrician to avoid hazards.
- Do not attempt to modify the lamp in any way.
3. Package Contents
Please check that all components are present and undamaged:
- Lamp Pole with Branches
- Lamp Base
- 3 x Globe Lampshades
- Power Cord with Foot Switch
- Assembly Hardware (screws, washers, etc.)
Note: Light bulbs are not included and must be purchased separately.
4. Assembly Instructions
Follow these steps to assemble your HOMCOM floor lamp:
- Attach the Lamp Pole to the Base: Carefully align the bottom section of the lamp pole with the central hole in the lamp base. Secure it using the provided screws and tighten them firmly.
- Connect the Power Cord: Ensure the power cord is properly routed through the base and connected securely.
- Install the Globe Lampshades: For each light branch, carefully screw the globe lampshade onto the lamp holder. Ensure it is securely fastened but do not overtighten.
- Insert Light Bulbs: Screw three E26 base bulbs (max 40W each, not included) into the lamp holders. Refer to Section 5 for important bulb compatibility notes.


5. Operating Instructions
Power Connection: Plug the lamp's power cord into a standard 120V AC electrical outlet.
Turning On/Off: The lamp is equipped with an on/off foot switch located on the power cord. Press the switch with your foot to turn the lamp on or off.

Bulb Compatibility: This lamp requires three E26 base bulbs, with a maximum wattage of 40W per bulb. Compatible bulb types include halogen bulbs and LED bulbs. Due to the design of the globe lampshades, it is recommended to use smaller form-factor E26 bulbs, such as chandelier-style bulbs or LED corncob bulbs, to ensure proper fit within the globe and allow the shade to be securely attached.

6. Maintenance
Cleaning: Disconnect the lamp from the power supply before cleaning. Use a soft, dry cloth to wipe down the lamp pole and base. For the glass globe shades, a slightly damp cloth can be used, followed by a dry cloth to prevent water spots. Do not use abrasive cleaners or solvents.
Bulb Replacement: Ensure the lamp is unplugged and the bulbs have cooled completely before attempting to replace them. Unscrew the old bulb and screw in a new E26 base bulb (max 40W). Ensure the new bulb is securely seated.
7. Troubleshooting
- Lamp does not turn on:
- Check if the power cord is securely plugged into the outlet.
- Ensure the foot switch is pressed to the 'on' position.
- Verify that the light bulbs are correctly installed and not burnt out.
- Check the circuit breaker in your home.
- Bulb does not fit inside the globe shade:
- Standard A19 E26 bulbs may be too large for the globe shades. Consider using smaller E26 bulb types such as B10 (chandelier) bulbs or LED corncob style bulbs.
- Ensure the globe shade is properly aligned and screwed on.
- Lamp is unstable:
- Ensure the lamp pole is securely fastened to the base.
- Place the lamp on a flat, level surface.
8. Specifications
| Model Number | B31-319V80 |
| Brand | HOMCOM |
| Overall Dimensions | 10.75"D x 10.75"W x 66.5"H |
| Item Weight | 13 Pounds |
| Material | Metal (Alloy Steel Base), Glass (Shades) |
| Finish Type | Plating |
| Color | Gold |
| Number of Light Sources | 3 |
| Bulb Base | E26 |
| Max Wattage per Bulb | 40W |
| Power Source | Corded Electric |
| Voltage | 120 Volts |
| Switch Type | Foot Switch |
| Indoor/Outdoor Usage | Indoor Use Only |
9. Product Video
Watch this video for a visual overview of the HOMCOM B31-319V80 Floor Lamp:
10. Warranty and Support
This HOMCOM floor lamp comes with a 1-year warranty against manufacturer defects. For warranty claims or technical support, please contact the retailer or manufacturer directly with your purchase details and model number (B31-319V80).