Introduction
This manual provides comprehensive instructions for the proper installation, use, and maintenance of your Wallbox Pulsar Plus Rain Cover. This accessory is designed to offer all-weather protection for your Wallbox Pulsar Plus EV charger, especially when mounted on an Effelberg Pedestal, safeguarding it from environmental elements such as rain, snow, dust, and UV radiation. Adhering to these instructions will help ensure the longevity and optimal performance of your EV charger and its protective cover.
Safety Information
Please read and understand all safety information before installing or using the rain cover. Failure to follow these instructions may result in damage to the product or personal injury.
- Ensure the EV charger is powered off and disconnected from the main power supply before handling or installing the cover.
- Do not attempt to modify the rain cover. Any modifications may compromise its protective capabilities.
- Keep the cover away from open flames or extreme heat sources.
- Regularly inspect the cover for any signs of wear, tear, or damage. Replace if necessary to maintain optimal protection.
- This cover is designed for the Wallbox Pulsar Plus EV charger and Effelberg Pedestal. Do not use it with other models or brands unless explicitly stated as compatible.
Package Contents
Verify that all items are present and undamaged before proceeding with installation.
- Wallbox Pulsar Plus Rain Cover (Model: COVER-EIFBS-PLP1)
- Instruction Manual (this document)
Installation Instructions
The Wallbox Pulsar Plus Rain Cover is designed for tool-free installation. Follow these steps to properly install the cover on your Wallbox Pulsar Plus EV charger and Effelberg Pedestal.
Step 1: Prepare the Charger
Ensure your Wallbox Pulsar Plus EV charger is securely mounted on the Effelberg Pedestal. Make sure the charging cable is properly coiled or stored in its designated holder, if applicable, to avoid interference during cover placement.
Image: A Wallbox Pulsar Plus EV charger is shown mounted on an Effelberg Pedestal, ready for the rain cover installation. The charger is dark gray with a green light indicator.
Step 2: Position the Rain Cover
Take the Wallbox Pulsar Plus Rain Cover. Identify the top and bottom of the cover. The top section typically has a wider overhang to shield the charger from above. Align the cover with the top of your Wallbox Pulsar Plus charger.
Image: The Wallbox Pulsar Plus Rain Cover, a dark gray L-shaped metal piece with pre-drilled holes and an oval cutout, is displayed from a front-side angle.
Step 3: Secure the Cover
Gently slide the rain cover over the Wallbox Pulsar Plus charger. The cover is designed to fit snugly around the charger and integrate with the Effelberg Pedestal. Ensure that the pre-drilled holes on the cover align with the corresponding mounting points on the pedestal or charger. The cover should rest securely, providing a protective shield over the charger unit.
Image: A Wallbox Pulsar Plus EV charger is shown with the dark gray rain cover successfully installed, mounted on an Effelberg Pedestal. The cover provides an overhead shield for the charger.
The cover should provide a seamless and secure fit, protecting the charger from direct exposure to weather elements.
Operating Instructions
Once installed, the Wallbox Pulsar Plus Rain Cover operates passively, providing continuous protection. No active operation is required.
- Continuous Protection: The cover remains in place to shield the charger from rain, snow, dust, and UV rays.
- Access for Charging: The design allows full access to the charging port and cable management without needing to remove the cover.
Maintenance
Regular maintenance ensures the rain cover continues to provide effective protection and maintains its appearance.
- Cleaning: Clean the cover periodically with a soft, damp cloth and mild soap. Avoid abrasive cleaners or solvents that could damage the finish.
- Inspection: Annually, or more frequently in harsh weather conditions, inspect the cover for any signs of damage, corrosion, or loose fittings. Ensure it remains securely attached and free from obstructions.
- Replacement: If the cover becomes significantly damaged or shows signs of compromised integrity, replace it to ensure continued protection for your EV charger.
Troubleshooting
This section addresses common concerns regarding the Wallbox Pulsar Plus Rain Cover.
| Problem | Possible Cause | Solution |
|---|---|---|
| Cover does not fit securely. | Incorrect alignment or not fully seated. | Re-align the cover and ensure it is pushed firmly into place, matching the mounting points of the charger and pedestal. Verify compatibility with your specific Wallbox Pulsar Plus model and Effelberg Pedestal. |
| Water accumulation on the charger despite cover. | Improper installation or extreme weather conditions. | Check that the cover is installed correctly and completely covers the top and sides of the charger. In severe weather, some moisture may still reach the charger, but the cover significantly reduces direct exposure. Ensure drainage is not blocked. |
| Cover appears damaged or worn. | Exposure to harsh elements or physical impact. | Inspect the extent of the damage. If the protective integrity is compromised, consider replacing the cover to ensure continued protection for your EV charger. |
Specifications
- Brand: Wallbox
- Model Number: COVER-EIFBS-PLP1
- Product Dimensions (W x H x D): 50 x 50 x 28 cm (approximately 19.7 x 19.7 x 11 inches)
- Item Weight: 1.46 Kilograms (approximately 3.22 lbs)
- Color: Traffic Gray
- Compatibility: Wallbox Pulsar Plus EV Charger, Effelberg Pedestal
- Material: Durable, weather-resistant material
Warranty and Support
For warranty information or technical support, please refer to the official Wallbox website or contact their customer service directly. Keep your purchase receipt as proof of purchase.
Wallbox Official Website: wallbox.com
