1. Introduction and Overview
The Enthuze ENT-TD6000 is a versatile device designed to provide emergency jump-starting for vehicles, inflate tires, and serve as a portable power bank. It also includes integrated LED light functions for various situations.
Key features include:
- Inflatable Function: Capable of inflating car tires, motorcycle tires, bicycle tires, air mattresses, water toys, and sports balls.
- Car Jump Start: Designed to jump-start 12V vehicle batteries using the included cables.
- Mobile Power Supply: Can charge/power cell phones, tablets, game consoles, cameras, and other digital smart devices.
- LED Light Functions: Features multiple LED light modes for illumination and signaling.
Figure 1: Enthuze ENT-TD6000 Jump Starter and included accessories.
2. Setup and Initial Use
2.1 Charging the Device
Before first use, fully charge the Enthuze ENT-TD6000. Connect the device to a suitable power source using the provided USB-C cable. The display will indicate the charging status. A full charge typically takes approximately 3.5 hours.
2.2 Connecting Jump Start Cables
To prepare for jump-starting, ensure the jump starter is adequately charged. Connect the smart battery clamp to the jump starter's designated port. The device will indicate readiness.
Video 1: Demonstration of connecting the smart battery clamp and jump-starting a vehicle.
3. Operating Instructions
3.1 Jump Starting a Vehicle
- Ensure the jump starter is fully charged.
- Connect the smart battery clamp to the jump starter.
- Attach the red (+) clamp to the positive terminal of the vehicle's battery.
- Attach the black (-) clamp to the negative terminal of the vehicle's battery or a solid, unpainted metal part of the engine block.
- Press the switch button on the jump starter to activate the jump-start function.
- Start the vehicle's engine.
- Once the vehicle starts, immediately remove the clamps from the vehicle battery, then disconnect the smart battery clamp from the jump starter.
This device is suitable for jump-starting vehicles with up to 8.0L gasoline engines and 6.0L diesel engines, including small cars, SUVs, pickup trucks, motorcycles, and boats.
3.2 Using the Air Compressor
- Screw the air hose into the designated port on the jump starter.
- Connect the other end of the air hose to the tire valve or the item to be inflated.
- Use the '+' or '-' buttons to set the desired air pressure.
- Press and hold the switch button for 3 seconds to start the inflation process.
- The device will automatically stop when the set pressure is reached.
- Disconnect the air hose from the item and the jump starter.
3.3 Using as a Power Bank
The Enthuze ENT-TD6000 features USB output ports to charge various electronic devices:
- USB Output 1: 5V=3A, 9V=2A, 12V=1.5A
- USB Output 2: 5V=2.1A
Connect your device to the appropriate USB port using a compatible charging cable.
3.4 LED Light Functions
The device includes multiple LED light modes:
- Stable Light: For general illumination.
- SOS Mode: For emergency signaling.
- Strobe Light: For attracting attention.
Press the light button to cycle through the different modes.
4. Maintenance
To ensure the longevity and optimal performance of your Enthuze ENT-TD6000, follow these maintenance guidelines:
- Regular Charging: Recharge the device every 3-6 months, even if not in use, to maintain battery health.
- Storage: Store the device in a cool, dry place. The recommended storage temperature should not be lower than -10°C or higher than 50°C. Extreme temperatures can shorten the product's life and damage the built-in battery.
- Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use harsh chemicals or abrasive materials.
- Cable Inspection: Periodically inspect the jump start cables and air hose for any signs of wear, damage, or corrosion. Replace if necessary.
Figure 2: Product with accessories and important warnings.
5. Troubleshooting
Refer to the table below for common issues and their solutions:
| Error Message | Cause | Solution |
|---|---|---|
| ERROR | Jumper cables connected with reversed polarity to the car battery. | Connect the battery clamps to the correct positive and negative terminals. |
| LOW | Correctly connected car battery, but battery voltage is below 9V, and the core temperature is above 0°C/32°F. | BOOST button for 2 seconds to use the forced boost function. |
| OUT IN | High-temperature protection activated, displaying core temperature overheating. | The product activates temperature protection below 50°C/122°F and resumes output when the temperature drops to 45°C/113°F. |
| IN | Low-temperature protection activated. | The product activates temperature protection below -10°C/-4°F and resumes output at 0°C/32°F-37°F. |
| START | Buzzer sounding, silence after 30 seconds. | Overcurrent detected, stop starting vehicle, disappear for 30S. |
| START | Vehicle start detected more than 5 times within 10 minutes, buzzer sounds buzzer mutes after 30S "START" continues to flash. | Stop starting the vehicle and the safety mode disappears after 10 minutes. |
6. Specifications
Detailed technical specifications for the Enthuze ENT-TD6000:
| Parameter | Value |
|---|---|
| Product Name | Jump Starter with Air Compressor |
| Model | ENT-TD6000 |
| Size | 193 x 110 x 53mm |
| Inflation Pressure Range | 0.2-8bar / 3-120psi |
| Operating Temperature | Charge: 0°C~45°C, Discharge: -10°C~45°C |
| Storage Temperature | -10°C~50°C |
| Inflatable Hose Length | 435mm (including air nozzle) |
| Battery Capacity | 41.44Wh (14.8V, 2.8Ah) |
| Working Noise | Less than 80dB away from 1 meter |
| Charging Input | 5V=3A |
| Charging Time | About 3.5 hours |
| USB Output 1 | 5V=3A, 9V=2A, 12V=1.5A |
| USB Output 2 | 5V=2.1A |
| Air Pressure Sensor Accuracy | ±1psi |
| Start Car Voltage | 12V |
| Start Car Current | 500A (1000A Peak) |
Figure 3: Basic Parameters of the Enthuze ENT-TD6000.
7. Important Safety Warnings
- Do not overcharge the internal battery. Refer to the instruction manual for proper charging procedures.
- Do not smoke, strike a match, or cause a spark in the vicinity of the power pack during operation.
- Only charge the internal battery in a well-ventilated area.
- Turn off the 12V firing output when the remaining power of the device's battery cell is less than 20%. USB port can output normally.
- Risk of Injury to Persons. Do not use this product if the power cord or the battery cables are damaged in any way.
- This device is not intended for use in a commercial repair facility.
- This device is intended to be stored indoors when not in use. This device shall not be stored or left outdoors when not in use.
- This device is intended for temporary use outdoors and reasonable care should be exercised when using this device in wet conditions.
8. Warranty and Support
For warranty information or technical support, please contact Enthuze Automotive Products directly. Keep your purchase receipt as proof of purchase.
