Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Gdrasuya10 Wave Round Dimmable LED Ceiling Light, Model S94. Please read this manual thoroughly before installation and retain it for future reference.
Image: The Gdrasuya10 Wave Round Dimmable LED Ceiling Light, Model S94, installed in a bedroom setting.
Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- 1 x Gdrasuya10 Wave Round Dimmable LED Ceiling Light
- 1 x Instruction Manual (this document)
- 1 x Hardware Bag (containing mounting screws, wire connectors, etc.)
- 1 x Remote Control
Important Safety Information
- Electrical Safety: For safe and secure installation, ensure that the electrical box to which this fixture will be mounted is properly attached to a structural member of the building. Always turn off power at the circuit breaker before installation or maintenance.
- Wiring: All wires are connected. When unpacking, be careful not to pull on wires as a bad connection may result. Do not connect electricity until your fixture is fully assembled.
- Professional Installation: If you are unsure about electrical wiring, consult a qualified electrician.
- Handling: Handle the light fixture with care to avoid damage to components, especially the acrylic lampshade and LED light sources.
Setup and Installation
This fixture is designed for flush mount installation. Ensure the power is OFF at the circuit breaker before beginning installation.
- Prepare the Mounting Surface: Ensure the electrical box is securely mounted to a structural support in the ceiling.
- Unpack Components: Carefully remove all parts from the packaging. Inspect for any damage.
- Attach Mounting Bracket: Secure the mounting bracket (from the hardware bag) to the electrical box using the provided screws.
- Wire Connections: Connect the household electrical wires to the fixture's wires according to local electrical codes. Typically, connect live to live (black to black), neutral to neutral (white to white), and ground to ground (green or bare copper to green). Use the provided wire connectors.
- Secure the Fixture: Carefully lift the light fixture and align it with the mounting bracket. Secure the fixture to the bracket using the screws provided. Ensure it is flush against the ceiling.
- Restore Power: Once the fixture is securely installed and all connections are made, restore power at the circuit breaker.
Image: Key components of the ceiling light, including the aluminum base, acrylic lampshade, and LED light source.
Operating Instructions
Your Gdrasuya10 LED Ceiling Light is controlled by the included remote control, allowing for adjustment of brightness and color temperature.
Remote Control Functions:
- Power On/Off: Press the power button to turn the light on or off.
- Brightness Adjustment: Use the brightness up/down buttons to adjust the light intensity from 1% to 100%.
- Color Temperature Adjustment: Use the color temperature buttons to cycle through or fine-tune the color temperature settings:
- Warm White: Approximately 3000K
- Neutral White: Approximately 4500K
- Cool White: Approximately 6000K - 6500K
Image: The remote control and visual representation of the light fixture displaying warm, neutral, and cool white color temperatures.
Image: Illustration of the dimming range (10%-100%) and color temperature options (3000K-6500K).
Maintenance
The Gdrasuya10 LED Ceiling Light requires minimal maintenance.
- Cleaning: Ensure the power is off before cleaning. Use a soft, dry cloth to wipe the fixture. For stubborn marks, a slightly damp cloth with mild soap may be used, followed by drying with a clean, dry cloth. Avoid abrasive cleaners or solvents.
- LED Longevity: The integrated LED light source is designed for long-term use and does not require bulb replacement.
Troubleshooting
If you encounter issues with your ceiling light, refer to the following common problems and solutions:
- Light does not turn on:
- Check if the power switch is on.
- Verify that the circuit breaker is not tripped.
- Ensure all wire connections are secure.
- Confirm the remote control has working batteries and is pointed at the fixture.
- Light flickers or dims unexpectedly:
- Check for loose wire connections.
- Ensure the voltage supply is stable and within the specified range (110-220V).
- If using a wall dimmer, ensure it is compatible with LED dimmable fixtures.
- Remote control not working:
- Replace the batteries in the remote control.
- Ensure there are no obstructions between the remote and the light fixture.
If the problem persists after attempting these solutions, contact customer support.
Specifications
| Model Number | S94 |
| Brand | Gdrasuya10 |
| Type | Dimmable LED Ceiling Light, Flush Mount |
| Shape | Wave Round |
| Material | Acrylic, Aluminum, Iron, Metal |
| Product Dimensions (L x W x H) | 35.43" x 23.62" x 2.75" (90cm x 60cm x 7cm) |
| Power Source | Corded Electric |
| Voltage | 110-220V |
| Wattage | 72W |
| Luminous Flux | 5000LM |
| Light Source Type | Integrated LED |
| Color Temperature | 3000K (Warm White) - 4500K (Neutral White) - 6500K (Cool White) |
| Dimmable Range | 1% - 100% (via remote control) |
| Control Method | Remote Control |
| Suggested Room Area | 15-25㎡ (161-269 sq ft) |
| Applicable Room Types | Bedroom, Dining Room, Home Office, Kitchen, Living Room |
Image: Detailed dimensions of the ceiling light fixture.
Warranty and Support
Specific warranty details are not provided in this manual. For warranty information or technical support, please refer to your purchase documentation or contact the retailer where the product was purchased.
