Introduction
This manual provides detailed instructions for the installation, setup, operation, and maintenance of your GUARDER Keyless Entry Door Lock Set. This advanced lock system offers multiple access methods including fingerprint recognition, keypad codes, and traditional mechanical keys, enhancing security and convenience for your home. It is designed for durability across various seasons and features an auto-lock function for added peace of mind.
Image: Overview of the Guarder Keyless Entry Door Lock Set highlighting its multifunctionality, including fingerprint access, IP56 waterproofing, support for 300 users, silent mode, auto-lock, emergency power, code protection, and mechanical key access.
Safety Information
General Safety Precautions
- Read all instructions carefully before installation and use.
- Keep backup keys in a secure location outside your home.
- Do not expose the lock to extreme temperatures or direct water spray beyond its IP66 rating.
- Ensure proper battery installation and replace batteries promptly when the low battery indicator appears.
Battery Safety
- Use 4 AAA alkaline batteries (not included). Do not mix old and new batteries or different types of batteries.
- Remove batteries if the product is not used for an extended period.
- Dispose of used batteries according to local regulations.
Package Contents
Verify that all components are present before beginning installation:
- Door Knob
- Latch
- Strike Plate
- 2 Backup Keys
- Mounting Plate
- Screws
- Smart Deadbolt with Fingerprint/Keypad Code/Key
- User Manual
Specifications
| Feature | Detail |
|---|---|
| Brand | GUARDER |
| Special Feature | Smart Deadbolt with Fingerprint/Keypad Code/Key |
| Lock Type | Biometric |
| Item Dimensions (L x W x H) | 3.94 x 9.45 x 18.11 inches |
| Material | Metal |
| Item Weight | 3.34 pounds |
| Model Name | Deadbolt+Knob |
Installation Guide
Pre-Installation Checklist
- Ensure your door thickness is between 1 3/8" to 2" (35mm to 50mm).
- Verify the latch length (backset) is either 2-3/8" (60mm) or 2-3/4" (70mm).
- Common household tools like a screwdriver or drill are required.
- Remove any existing lock hardware from your door.
Image: A diagram illustrating the necessary door dimensions, including door thickness (1-3/8" to 2"), backset (2.13"), and adjustable latch length (2-3/8" or 2-3/4").
Step-by-Step Installation
1. Install Latch
Insert the latch into the door edge. Ensure the latch is oriented correctly for your door's swing direction. Secure with screws.
2. Install Exterior Keypad
Carefully route the power cable through the door hole and align the exterior keypad with the latch. Ensure the lock bar is inserted horizontally.
Image: The exterior keypad of the Guarder Keyless Entry Door Lock Set, featuring the numerical keypad and fingerprint sensor.
3. Install Gasket and Mounting Plate
Place the gasket on the interior side of the door, ensuring the convex side faces out. Then, attach the mounting plate over the gasket, securing it with screws. Connect the power cable from the exterior keypad to the interior assembly.
Image: An exploded view of the internal lock components, including the mounting plate, gasket, and wiring, illustrating how they fit together during installation.
4. Install Interior Assembly
Align the interior assembly with the mounting plate and secure it with the remaining screws. Ensure all wires are tucked away neatly to avoid pinching.
Image: The interior assembly of the Guarder Keyless Entry Door Lock Set, showing the battery compartment and manual turn knob, being attached to the door.
5. Install Batteries and Cover
Insert 4 AAA batteries into the battery compartment. Close the battery cover securely.
Image: The battery compartment of the interior lock assembly, showing the slots for AAA batteries.
Setup and Programming
Initial Setup
After installation, perform the following steps to configure your lock.
1. Detect Left/Right Hand Door Installation
This step ensures the lock motor operates in the correct direction for your door. Follow the on-screen instructions or refer to the video for guidance.
2. Turn On Auto-lock & Set Time Delay
The auto-lock feature automatically locks the door after a set delay (5-69 seconds). You can configure this delay time.
3. Turn Auto-lock OFF
If you prefer to manually lock your door, you can disable the auto-lock feature. The initial state of the lock is without auto-lock enabled.
4. Add New User Code
You can add up to 250 unique 4-9 digit user codes. Ensure new passcodes are different from existing ones.
5. Changing User Code
Modify existing user codes as needed. The new passcode must be different from all other passcodes currently in the lock.
6. Delete All User Codes At Once
This function allows you to delete all user codes simultaneously. The programming code will remain unchanged.
7. Change Programming Code
The programming code is a master code used for all programming functions. It should be 4-10 digits in length.
8. Add New Fingerprint
The lock can store up to 50 unique fingerprints. Follow the prompts to register your fingerprint by placing your finger on the sensor 5 times.
Image: The main product image showing the exterior keypad with a prominent fingerprint sensor at the bottom.
9. Delete Fingerprint
Remove registered fingerprints from the lock's memory.
10. Turn On/Off Sound
You can enable or disable the sound feedback from the lock. Note that the low battery beep will still sound even if the general sound is off.
Operating Instructions
Unlocking the Door
Your GUARDER lock offers multiple convenient ways to unlock your door:
Unlocking with Fingerprint
Place your registered finger on the fingerprint sensor. The lock will unlock in under 1 second if the fingerprint is recognized.
Image: Two children demonstrating unlocking methods: one using a fingerprint for quick access (1.5 seconds unlock speed) and another using a keypad code with the code protect feature.
Unlocking with Keypad Code
Enter your 4-9 digit user code on the backlit keypad. The lock will unlock upon correct entry. Use the code protect function to hide your actual code within a longer sequence of numbers.
Unlocking with Mechanical Key
In case of emergency or battery depletion, use one of the provided backup mechanical keys to unlock the door.
Locking the Door
You can secure your door using the auto-lock feature or by manually locking it.
Auto-Lock Feature
If enabled, the lock will automatically engage the deadbolt after a preset delay (5-69 seconds) once the door is closed.
Image: A woman entering her home with groceries, illustrating the auto-lock feature which secures the door automatically after a set interval (5-69 seconds).
Manual Locking
To manually lock the door from the outside, long-press the lock button on the keypad for 3 seconds. From the inside, turn the manual knob to engage the deadbolt.
Maintenance
Battery Replacement
The lock requires 4 AAA batteries, which typically last an average of 12 months. A low battery reminder will alert you when replacement is needed. To replace, remove the interior cover, swap the old batteries with new ones, and reattach the cover.
Cleaning
Clean the lock's exterior with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish or electronic components.
Troubleshooting
- Lock not responding: Check battery levels and replace if necessary. Ensure the power cable is securely connected.
- Keypad not lighting up: Verify battery installation and charge.
- Motor not turning with deadbolt: Ensure the lock cylinder is horizontal during installation. Check for any obstructions in the door frame or latch mechanism.
Warranty and Support
The GUARDER Keyless Entry Door Lock Set is designed for durability, with an IP66 waterproof and dustproof rating and a 1-year battery life. For any questions or assistance, GUARDER offers online after-sales call service from Monday to Sunday, 9 am to 6 pm PDT, and 24/7 online after-sales email service.
