1. Introduction and Safety Information
This manual provides detailed instructions for the safe installation and operation of your Pipishell Full-Motion TV Wall Mount PILF8. Please read all instructions carefully before installation to ensure proper setup and to prevent personal injury or property damage. Keep this manual for future reference.
Important Safety Warnings:
- Weight Capacity: Do not exceed the maximum weight capacity of 100 lbs (45.5 kg). Exceeding this limit may result in serious injury or property damage.
- TV Size: This mount is designed for most 37-75 inch TVs. Ensure your TV falls within this range.
- Wall Type: This mount is compatible with 16-inch wood studs, concrete, and brick walls. Do not install on drywall alone.
- Professional Installation: If you are unsure about the installation process, consult a qualified professional.
- Component Check: Verify that all components are present and undamaged before installation. Do not use damaged parts.
- Tools: Use appropriate tools for installation.
2. Package Contents
Before beginning installation, ensure all parts are included in your package. Refer to the parts list in your physical instruction manual for specific hardware identification. The package typically includes:
- Wall Plate Assembly
- TV Brackets (2 pieces)
- Mounting Hardware Kit (various screws, washers, spacers for TV and wall)
- Drilling Template
- Bubble Level
- Cable Ties (Hook & Loop Fasteners)
- Instruction Manual
Image 2.1: Overview of the Pipishell Full-Motion TV Wall Mount PILF8 and its components, including the main mount assembly, TV brackets, cable ties, and a bubble level.
3. Compatibility Check
Confirm your television and wall meet the following requirements for safe installation:
- TV Size: Compatible with most 37 to 75 inch flat or curved televisions.
- TV Weight: Supports televisions weighing up to 100 lbs (45.5 kg).
- VESA Pattern: Supports VESA mounting patterns from 200x100mm to 600x400mm. Measure the horizontal and vertical distance between the mounting holes on the back of your TV.
- Wall Type: Designed for installation on 16-inch wood studs, solid concrete, or brick walls. Not for drywall installation only.
Image 3.1: Visual representation of the mount's wide compatibility, indicating supported TV sizes, maximum weight, and VESA mounting patterns.
4. Setup and Installation
Follow these steps carefully for a secure installation. It is recommended to have two people for installation, especially when lifting the TV.
Step 4.1: Attach TV Brackets to Your TV
- Carefully place your TV face-down on a soft, clean surface to prevent screen damage.
- Identify the correct diameter and length of screws for your TV's VESA mounting holes. Use the provided hardware kit.
- Attach the two TV brackets to the back of your TV using the selected screws and washers. Ensure the brackets are centered and securely fastened. Do not overtighten.
Image 4.1: Demonstrates the process of securing the TV brackets to the rear of the television using appropriate screws.
Step 4.2: Mount the Wall Plate to the Wall
- Determine the desired height for your TV. Use the provided drilling template to mark the pilot hole locations on the wall. Ensure the template is level using the included bubble level.
- For wood stud installation: Locate the center of your 16-inch wood studs. Drill pilot holes using a 7/32 inch (5.5mm) drill bit.
- For concrete/brick wall installation: Drill pilot holes using a 3/8 inch (10mm) drill bit. Insert concrete anchors into the drilled holes.
- Align the wall plate with the pilot holes and secure it to the wall using the lag bolts and washers. Tighten all bolts firmly.
Image 4.2: A drilling template and bubble level are used to accurately mark the mounting points on the wall, ensuring correct stud spacing.
Image 4.3: Shows the wall plate being securely fastened to the wall using the provided lag bolts.
Step 4.3: Hang Your TV on the Wall Plate
- With assistance, carefully lift the TV with the attached brackets and hook them onto the wall plate assembly.
- Ensure the TV is securely seated on the mount.
- Engage the security screws or locking mechanisms on the TV brackets to prevent accidental dislodgement.
Image 4.4: Depicts the final step of hanging the television onto the pre-installed wall mount.
5. Operating Instructions (Adjustments)
Your Pipishell Full-Motion TV Wall Mount offers various adjustments for optimal viewing.
5.1 Swivel Adjustment
The mount allows for a smooth swivel of +/-45° to achieve the perfect viewing angle from different positions in the room. Gently push or pull the TV to the desired left or right position.
Image 5.1: Illustrates the swivel capability of the mount, allowing the TV to be angled up to 45 degrees left or right.
5.2 Tilt Adjustment
Adjust the tilt angle to reduce glare and improve viewing comfort. The mount offers a tilt range of +5° (upward) to -15° (downward). Loosen the tilt adjustment knobs, set the TV to the desired angle, and then re-tighten the knobs.
Image 5.2: Shows the tilt function, enabling adjustment of the TV's vertical angle to minimize glare and enhance viewing.
5.3 Extension and Retraction
The articulating arms allow the TV to extend smoothly up to 15.4 inches (39.1 cm) from the wall for maximum flexibility and retract back to 3.2 inches (8.1 cm) to save space. Gently pull or push the TV to adjust its distance from the wall.
Image 5.3: Illustrates the mount's ability to extend the TV up to 15.4 inches from the wall and retract it to 3.2 inches, optimizing space and viewing flexibility.
5.4 Post-Installation Leveling
After installation, the TV can be leveled +/-3° to ensure it is perfectly horizontal. Loosen the leveling screws, adjust the TV, and then re-tighten the screws.
Image 5.4: Shows the post-installation leveling feature, allowing for minor rotational adjustments to ensure the TV is perfectly straight.
5.5 Cable Management
Use the provided hook & loop fasteners to route cables along the articulating arms for a neat and organized appearance.
Image 5.5: Demonstrates how to use cable ties to manage and conceal cables along the mount's arms for a tidy setup.
6. Maintenance
Regular maintenance helps ensure the longevity and safe operation of your TV wall mount.
- Cleaning: Wipe the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Periodic Checks: Periodically check all screws and bolts to ensure they remain tight. Re-tighten if necessary.
- Movement: If the mount's movement becomes stiff, apply a small amount of silicone-based lubricant to the articulating joints.
7. Troubleshooting
If you encounter issues during or after installation, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level after installation. | Minor misalignment during installation. | Use the post-installation leveling feature (Section 5.4) to adjust the TV. |
| Mount feels loose or unstable. | Wall bolts or TV screws are not sufficiently tightened. Incorrect wall type. | Ensure all wall bolts and TV screws are securely tightened. Verify wall type compatibility (Section 3). |
| Difficulty moving the TV (swivel, tilt, extension). | Joints may be stiff or overtightened. | Check for any overtightened bolts on the articulating arms. Apply silicone-based lubricant to joints if necessary. |
| TV does not fit the mount. | Incorrect TV size, weight, or VESA pattern. | Re-check TV compatibility with the mount's specifications (Section 3). |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | PILF8 |
| Brand | Pipishell |
| Compatible TV Sizes | 37 - 75 inches |
| Maximum Weight Capacity | 100 lbs (45.5 kg) |
| VESA Compatibility | 200x100mm to 600x400mm |
| Movement Type | Full Motion (Articulating, Swivel, Tilt, Level) |
| Swivel Range | +/-45° |
| Tilt Range | +5° / -15° |
| Level Adjustment | +/-3° |
| Extension from Wall | 3.2 inches (retracted) to 15.4 inches (extended) |
| Compatible Wall Types | 16-inch Wood Studs, Concrete, Brick |
| Material | Alloy Steel |
| Product Dimensions | 17.32 x 9.33 x 3.11 inches (packaged) |
| Item Weight | 10.85 pounds |
9. Warranty and Support
For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official Pipishell website. Keep your purchase receipt as proof of purchase.
