1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your LYONGTECH Multifunction Display Battery Charger. This two-way LCD charging hub is designed for DJI Mini 4 Pro, Mini 3, and Mini 3 Pro batteries, including battery plus versions. It offers multiple charging modes, battery information display, and power bank functionality.
2. Package Contents
- 1 x LYONGTECH LCD Battery Charger
- 1 x USB-A to USB-C Charging Cable
- 1 x USB-C to USB-C Charging Cable
Note: USB-A output cable and batteries are not included.

3. Setup
- Connect Power: Connect the charger to a power source using the provided USB-C to USB-C cable or USB-A to USB-C cable. For optimal performance, use a Power Delivery (PD) charger with an output of 45W or higher.
- Insert Batteries: Carefully insert your DJI Mini 4 Pro or Mini 3 Series batteries into the designated slots on the charging hub. Ensure each battery is fully seated until a click is heard.
- Cable Connection Check: Ensure USB-C cables are pushed in until a click is heard. If not fully inserted, the charging hub may not charge, and the display might show "0" for voltage/power or no display at all.

4. Operating Instructions
4.1 Charging Modes
The charger supports three distinct charging modes:
- Full Charge Mode: Charges batteries to 100% capacity.
- Storage Charge Mode: Charges batteries with less than 60% to 60-65% for long-term storage. If a battery's level is already above 60%, it will not be charged in this mode.
- Discharge Mode: Allows using the drone battery as a power bank to charge other devices.
4.2 Charging Method and Speed
- Input ≥ PD 45W: Two batteries are charged simultaneously (in parallel).
- Two Mini 4 Pro batteries: Approximately 65 minutes.
- Two Mini 3 batteries: Approximately 60 minutes.
- Two Mini 3/4 Battery Plus batteries: Approximately 90 minutes.
- Input > PD 35W (but < PD 45W): The battery with the higher charge level receives high current, and the remaining current charges the second battery.
- Input ≤ PD 35W: Batteries are charged one by one, with the battery having the higher charge level being charged first.
Tip: Using a charger less than PD 45W or without a PD mark will result in slower charging speeds or sequential charging.


4.3 Power Bank Function
The charger can utilize your Mini 3/4 battery to act as a power bank. Connect your remote controller or other USB devices to the USB output port on the charger to begin charging them.

4.4 Checking Battery Levels
The integrated LCD display allows you to quickly check the battery levels, voltage, and cycle count of your Mini 3/4 batteries without needing to insert them into your drone.

5. Specifications
| Feature | Specification |
|---|---|
| Product Dimensions | 6.3D x 6W x 8.4H Centimetres |
| Item Weight | 159 Grams |
| Input Voltage | 5V/9V/12V/15V/20V--3A (Max) |
| Battery Output | 8.6/8.5V 2.5A x 2 (Max) |
| USB Output | 5V/2A (Max) |
| Connector Type | USB-C |
| Number of Ports | 2 (for batteries) + 1 (USB-A output) |
| Typical Charging Time (2 batteries, ≥PD 45W) | Mini 4 Pro: ~65 mins; Mini 3: ~60 mins; Mini 3/4 Plus: ~90 mins |
6. Troubleshooting
- Charger not powering on or displaying information:
- Ensure the power cable is securely connected to both the charger and the power source.
- Verify the power source is active and providing sufficient power.
- Check if the USB-C input cable is fully inserted until it clicks.
- Batteries not charging or charging slowly:
- Confirm batteries are correctly inserted into their slots.
- Ensure your power adapter is Power Delivery (PD) compatible and provides at least 45W for simultaneous fast charging. Lower wattage adapters will charge slower or sequentially.
- In Storage Mode, batteries already above 60% will not charge further.
- LCD display shows "0" or is blank:
- This often indicates an issue with the battery connection or the input power cable not being fully inserted. Re-insert batteries and cables firmly.
7. Maintenance
- Keep the charger clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the charger to extreme temperatures, moisture, or direct sunlight.
- Store the charger in a cool, dry place when not in use.
- Do not attempt to disassemble or repair the charger yourself. Contact customer support for assistance.
8. Official Product Videos
LYONGTECH Multifunction LCD Charger for Mini 4 Pro, Mini 3 Series
This video demonstrates the key features and operation of the LYONGTECH Multifunction LCD Charger, including its compatibility with DJI Mini 4 Pro and Mini 3 series batteries.
FPVtosky Mini 4 Pro Charger Hub Video
A short video showcasing the FPVtosky charger hub, which is functionally similar to the LYONGTECH model for DJI Mini 4 Pro batteries, demonstrating charging and discharge capabilities.
9. Warranty and Support
For warranty information and customer support, please refer to the product packaging or contact LYONGTECH directly through their official channels. Keep your purchase receipt for warranty claims.