FAITHSAIL 8FT LED Shop Light Instruction Manual

1. Introduction

Thank you for choosing the FAITHSAIL 8FT LED Shop Light. This ultra-slim, high-efficiency LED wraparound strip light is designed to provide superior illumination for various indoor environments such as garages, workshops, offices, and basements. It serves as an energy-saving replacement for traditional fluorescent fixtures, offering bright, uniform, and flicker-free lighting.

Please read this manual thoroughly before installation and operation to ensure safe and proper use of the product. Keep this manual for future reference.

2. Safety Information

• WARNING: Risk of electric shock. Disconnect power before installation or servicing.
• Installation should be performed by a qualified electrician in accordance with all national and local electrical codes.
• Do not install near heat sources or in areas with high humidity.
• Ensure the supply voltage is compatible with the fixture's requirements (100-227V AC, 60Hz).
• Do not look directly into the LED light source when illuminated.
• This fixture is designed for indoor use only.

3. Package Contents

Verify that all components are present and undamaged upon opening the package:

• 1 x FAITHSAIL 8FT LED Wraparound Light Fixture
• 1 x Hardware Kit (screws, wire nuts, etc.)
• 1 x User Manual

4. Specifications

Figure 1: Key Technical Specifications

Figure 2: Product Dimensions

5. Setup and Installation

The FAITHSAIL 8FT LED Shop Light is designed for straightforward installation. Follow these steps carefully:

1. Disconnect Power: Before beginning any electrical work, ensure the power supply to the installation area is turned off at the circuit breaker.
2. Prepare the Fixture: Unscrew the black screws located at the ends of the light fixture. Carefully remove the middle black metal plate to access the wiring compartment.
3. Mount the Fixture: Position the light fixture on the ceiling or desired mounting surface. Mark the locations for mounting screws. Secure the fixture using the provided hardware, ensuring it is firmly attached.
4. Wire Connections: Connect the electrical wires from your power source to the corresponding wires in the fixture's junction box. Typically, this involves connecting live to live, neutral to neutral, and ground to ground using appropriate wire nuts.
5. Secure Wiring and Reassemble: Ensure all wire connections are secure and properly insulated. Carefully replace the black metal plate and fasten it with the black screws.
6. Restore Power: Once installation is complete and all connections are secure, restore power at the circuit breaker.

Figure 3: Installation Steps

The fixture features an ultra-slim profile and lightweight construction, making it easy to handle during installation. It also includes integrated LED strips for soft, glare-free illumination.

6. Operating Instructions

Once installed and powered, the FAITHSAIL 8FT LED Shop Light operates like any standard light fixture. Use your wall switch or connected control method to turn the light on and off. The LED fixture provides instant-on illumination without flickering or delay.

• On/Off: Toggle the connected wall switch to turn the light fixture on or off.
• Brightness: This model is not dimmable and provides full brightness (12600 Lumens) when turned on.
• Linkable Feature: Multiple fixtures can be linked end-to-end (up to 8 fixtures) by knocking out the end hole and connecting the wires correctly. Consult a qualified electrician for complex linking setups.

7. Maintenance

The FAITHSAIL 8FT LED Shop Light is designed for long-term, maintenance-free operation with a lifespan exceeding 50,000 hours. No bulb replacement is necessary.

• Cleaning: To clean the fixture, ensure power is disconnected. Use a soft, dry, or slightly damp cloth. Do not use abrasive cleaners or solvents.
• Inspection: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician.

8. Troubleshooting

If you encounter any issues with your FAITHSAIL 8FT LED Shop Light, refer to the following common troubleshooting steps:

• Light does not turn on:
  • Check if the power supply to the fixture is active at the circuit breaker.
  • Ensure all wire connections are secure and correct.
  • Verify the wall switch is in the 'ON' position.
• Light flickers:
  • Confirm the fixture is not connected to a dimmer switch, as this model is not dimmable.
  • Check for loose wiring connections.
  • Ensure the voltage supply is stable and within the specified range.
• Light is dim:
  • Ensure the fixture is receiving full power.
  • Clean the light diffuser if dust or debris has accumulated.

If these steps do not resolve the issue, please contact FAITHSAIL customer support for assistance.

9. Warranty and Support

FAITHSAIL products are manufactured to high-quality standards and are backed by a manufacturer's warranty. Please refer to the product packaging or contact customer service for specific warranty details and duration.

For technical support, warranty claims, or any questions regarding your FAITHSAIL 8FT LED Shop Light, please contact our customer service team:

• Email: support@faithsail.com (Example)
• Phone: 1-800-XXX-XXXX (Example)
• Website: Visit the FAITHSAIL Store on Amazon