LUXBIRD LB-2SC Digital Heating Mat Thermostat Controller User Manual

1. Introduction

The LUXBIRD LB-2SC Digital Heating Mat Thermostat Controller is designed to precisely control the temperature of heating mats and other heating devices. Featuring dual independent outlets and two temperature probes, it allows for simultaneous control of two separate heating environments. This controller is ideal for a variety of applications including seedling germination, reptile habitats, home brewing, breeding, incubation, and greenhouse temperature management. Its user-friendly interface and advanced alarm functions ensure optimal conditions and safety for your specific needs.

2. Safety Information

• Read all instructions carefully before use.
• Do not immerse the controller unit in water or expose it to excessive moisture.
• Ensure the total wattage of connected devices does not exceed 250W per outlet or 500W total.
• Keep out of reach of children and pets.
• Unplug the unit from the power outlet before cleaning or performing any maintenance.
• Do not use if the power cord, probes, or unit itself is damaged.
• For indoor use only.

3. Package Contents

• 1 x LUXBIRD LB-2SC Digital Heating Mat Thermostat Controller
• 2 x Temperature Probes with Suction Cups
• 1 x User Manual (this document)

4. Product Overview

The LUXBIRD LB-2SC controller features a clear LCD display and intuitive buttons for easy operation. It includes two independent probe inputs (P1, P2) and two corresponding power outlets (WORK1, WORK2).

Figure 4.1: LUXBIRD LB-2SC Digital Heating Mat Thermostat Controller with its two temperature probes.

Figure 4.2: Detailed diagram of the controller's display and connection points.

Key Components:

• LCD Display: Shows current temperature, set temperature, and heating status for both P1 and P2.
• Menu Button (≡): Used to access settings and confirm selections.
• Down Button (∨): Decreases values or navigates menu options.
• Up Button (∧): Increases values or navigates menu options.
• P1/P2 Probe Sockets: Connect the temperature probes.
• WORK1/WORK2 Thermostat Sockets: Connect heating devices (e.g., heating mats).
• Hanging Tab: For convenient mounting of the unit.

5. Setup

1. Placement: Choose a suitable location for the controller. It has a hanging tab for easy mounting. Ensure it is away from direct heat sources or excessive moisture.
2. Connect Probes: Insert the two temperature probes into the P1 and P2 sockets on the sides of the controller. Place the probe tips in the desired temperature monitoring locations (e.g., soil for seedlings, inside a reptile enclosure). Use the included suction cups to secure the probes if needed.
3. Connect Heating Devices: Plug your heating mats or other heating devices into the WORK1 and WORK2 outlets at the bottom of the controller. Ensure the total wattage for each outlet does not exceed 250W, and the combined total does not exceed 500W.
4. Power On: Plug the controller's power cord into a standard 100-240VAC, 50/60Hz electrical outlet. The LCD display will light up.

Figure 5.1: Example setup showing the controller connected to heating mats for plants.

Figure 5.2: The controller's hanging tab allows for flexible placement.

6. Operating Instructions

6.1. Setting Target Temperature (P1/P2)

1. Press the Menu (≡) button once. The P1 set temperature will flash.
2. Use the Up (∧) or Down (∨) buttons to adjust the desired target temperature for P1.
3. Press the Menu (≡) button again to confirm P1 setting and move to P2. The P2 set temperature will flash.
4. Use the Up (∧) or Down (∨) buttons to adjust the desired target temperature for P2.
5. Press the Menu (≡) button a third time to confirm P2 setting and exit the setting mode.

Figure 6.1: The controller supports a wide temperature control range.

6.2. Switching Temperature Units (°C/°F)

To switch between Fahrenheit (°F) and Celsius (°C):

• With the unit in normal operating mode (not in setting mode), press and hold the Up (∧) button for approximately 3 seconds. The display will switch units. Repeat to switch back.

Figure 6.2: Easily switch between Fahrenheit and Celsius units.

6.3. High/Low Temperature Alarms

The controller features audible alarms to alert you if the detected temperature falls outside your desired range or if a probe abnormality occurs.

• When the temperature exceeds the set high limit or drops below the set low limit, the alarm will sound.
• If a probe is disconnected or faulty, an alarm will also sound.
• To silence the alarm, press any button.

Figure 6.3: The controller provides high/low temperature and probe abnormality alarms.

6.4. Real-Time Temperature Monitoring

The informative LCD display allows you to view the current temperature measured by each probe (P1 and P2), their respective target temperatures, and the heating status (indicated by a heating icon) at a glance.

Figure 6.4: The included premium precision probes ensure accurate temperature readings.

7. Maintenance

• Cleaning: Disconnect the controller from the power outlet. Wipe the unit and probes with a soft, damp cloth. Do not use abrasive cleaners or immerse the unit in water.
• Storage: When not in use for extended periods, store the controller in a cool, dry place, away from direct sunlight and extreme temperatures.
• Probe Care: Handle probes carefully. Avoid bending or kinking the cables. Clean probe tips regularly to ensure accurate readings.

8. Troubleshooting

9. Specifications

10. Warranty and Support

For detailed warranty information, technical support, or further assistance, please refer to the official user manual PDF provided by Luxbird or visit the Luxbird website.

You can access the full User Manual (PDF) here.