Upgraded Remote Control Thermostat Kit

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new Upgraded Remote Control Thermostat Kit. This kit is designed to provide convenient remote control and thermostatic operation for millivolt gas valve fireplaces and stoves.

Key Features:

• Blue backlit LCD display for enhanced visibility.
• Remote control for On/Off functionality and temperature setting.
• Easy access sliding battery compartment on receiver.
• Pre-programmed for quick installation.
• Direct replacement for various fireplace brands including SKYTECH, Ambient, Majestic, Monessen, and Vermont Castings.

Important Safety Information

Attention: This kit is not compatible with latching solenoid gas valve systems. Please consult your fireplace's instruction manual to ensure correct application before purchase.

This remote-control system is intended for use with millivolt or 24V gas valve systems only. Do not use this system with applications exceeding 24 Volts AC/DC and 1 amp current. The remote receiver must be kept away from temperatures exceeding 130°F (54°C) to prevent damage and ensure safe operation.

Package Contents

Verify that all components are present in your package:

• Remote Control Unit
• Receiver Unit
• Wall Plate
• Wiring (for receiver connection)
• Mounting Screws and Anchors

Image: The complete kit includes the remote, receiver, wall plate, wiring, and mounting hardware.

Setup

1. Battery Installation

The system requires two (2) 'AAA' batteries for the remote control and four (4) 'AA' batteries for the receiver. Batteries are not included.

• Remote Control: Open the battery compartment on the back of the remote and insert two 'AAA' batteries, observing the correct polarity (+/-).
• Receiver Unit: Slide open the battery cover on the receiver unit. Insert four 'AA' batteries, ensuring correct polarity.

Image: The receiver unit with its battery compartment open, indicating the need for 4xAA batteries.

2. Connecting the Receiver to the Gas Valve

The receiver connects to any standard millivolt gas valve system. Ensure your fireplace is turned off and cooled before proceeding.

• Locate the millivolt gas valve in your fireplace. Identify the 'TH' and 'TH/TP' terminals.
• Connect the two wires from the receiver unit to the 'TH' and 'TH/TP' terminals of the millivolt valve. The connection is non-polarized, so the order of wires does not matter.

Image: A generic wiring diagram illustrating how to connect the receiver's wires to the 'TH' and 'TH/TP' terminals on a millivolt gas valve.

3. Pairing (Learning) the Remote and Receiver

The remote and receiver are pre-programmed, but if re-pairing is needed:

• Ensure both the remote and receiver have fresh batteries installed.
• On the receiver unit, locate the small 'LEARN' button (often a pinhole).
• Using a paper clip or similar pointed object, gently press and hold the 'LEARN' button on the receiver until you hear a beep.
• Immediately press any button on the remote control. The receiver will emit a series of beeps to confirm successful pairing.

Image: The receiver unit integrated with its wall plate, showing the 'LEARN' button and a note about the beep sound when successfully connected.

4. Mounting the Receiver

The receiver can be placed near the fireplace or mounted to a wall using the included wall plate and hardware.

• Choose a location where the receiver is protected from excessive heat and moisture, and within range of the remote control (up to 30 feet).
• If wall-mounting, use the wall plate as a template to mark screw holes. Drill pilot holes if necessary, insert anchors, and secure the wall plate with screws.
• Slide the receiver onto the mounted wall plate.

Operating Instructions

Once installed and paired, your remote control thermostat kit is ready for use.

Remote Control Functions:

• ON Button: Press to turn the fireplace ON.
• OFF Button: Press to turn the fireplace OFF.
• MODE Button: Toggles between manual ON/OFF mode and thermostatic (SET TEMP) mode.
• SET Button: Used to adjust the desired temperature in thermostatic mode.

Image: A hand holding the remote control, displaying its blue backlit screen with the word 'On', positioned in front of an active fireplace.

Thermostatic Operation:

In thermostatic mode, the fireplace will automatically turn on or off to maintain the set temperature.

• Press the MODE button until 'SET TEMP' or a temperature reading appears on the remote's display.
• Use the SET button to adjust the desired temperature. Each press will cycle through temperature settings.
• The remote will display the current room temperature and the set temperature. The fireplace will activate when the room temperature falls below the set temperature and deactivate when it rises above.

Image: A side-by-side comparison showing an older remote control version next to the upgraded version, highlighting the new blue backlit screen for improved visibility.

Maintenance

To ensure optimal performance and longevity of your remote control thermostat kit, follow these simple maintenance guidelines:

• Battery Replacement: Replace batteries in both the remote and receiver annually, or when the display dims or the range decreases. Always use fresh, high-quality batteries.
• Cleaning: Wipe the remote and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
• Storage: If storing the unit for an extended period, remove all batteries to prevent leakage.

Troubleshooting

If you encounter issues with your remote control thermostat kit, refer to the following common problems and solutions:

Specifications

Warranty Information

This product comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.

Please retain your proof of purchase for warranty claims.

Customer Support

For further assistance, technical support, or warranty inquiries, please contact the manufacturer or your place of purchase. Provide your product model number (RCB06A) and a detailed description of the issue when contacting support.