SOLTECH CCTV Remote Control User Manual

1. Introduction

This manual provides essential instructions for the SOLTECH CCTV Remote Control, model RCWN00001B (also identified as EP10-001090A). This remote is specifically designed for use with various Samsung Wisenet Security & Surveillance Camera Systems, including DVRs and NVRs. Please read this manual thoroughly to ensure proper use and functionality of your remote control.

2. Product Overview

The SOLTECH CCTV Remote Control is a dedicated device for managing your Samsung Wisenet security system. It replicates the functionality of the original remote control included with Wisenet All-In-One systems, providing convenient access to your DVR or NVR functions.

Image 2.1: Front view of the SOLTECH CCTV Remote Control (Model RCWN00001B / EP10-001090A).

Image 2.2: The remote control positioned on a Wisenet Digital Video Recorder (DVR).

3. Setup

This remote control requires two AAA batteries for operation. Batteries are not included with the product and must be purchased separately.

3.1 Battery Installation

1. Locate the battery compartment on the back of the remote control.
2. Slide the battery compartment cover downwards and lift it off.
3. Insert two AAA batteries, ensuring correct polarity (+ and -) as indicated inside the compartment.
4. Replace the battery compartment cover by sliding it back into place until it clicks securely.

Image 3.1: Rear view of the remote control with the battery compartment open, showing where to insert AAA batteries.

3.2 Initial Connection

The SOLTECH CCTV Remote Control is pre-configured for Samsung Wisenet All-In-One System DVRs and NVRs. No additional setup, programming, or pairing is required. Once batteries are installed, the remote is ready for immediate use with compatible systems.

Image 3.2: The remote control shown alongside a Wisenet DVR, illustrating the 'no additional setup required' feature.

4. Operating Instructions

Point the remote control directly at your Samsung Wisenet DVR or NVR. Press the desired buttons to navigate menus, control playback, switch camera views, and access other functions of your security system. The button layout is standard for Wisenet systems, allowing for intuitive operation.

• Number Buttons (0-9): Used for direct camera selection or data entry.
• Directional Pad (Up, Down, Left, Right, SEL): For menu navigation and selection.
• MUTE: Mutes audio output.
• SUBMENU: Accesses sub-menus within the system interface.
• Playback Controls (Play, Pause, Stop, Fast Forward, Rewind): Manages recorded footage playback.
• REC (Record): Initiates manual recording.

5. Compatibility

This remote control is compatible with various Samsung Wisenet All-In-One System Series. It is designed to function as a direct replacement for the original remote controls supplied with these systems.

5.1 Compatible System Series

The remote control is compatible with, but not limited to, the following Samsung Wisenet All-In-One System Series:

• SDH-E95127
• SDH-B94047
• SDH-C94087
• SDH-B73043
• SDH-C85080
• SDH-SF440
• SDH-B74043
• SDH-B74083
• SDH-B74041
• SDH-B74081
• SDH-C85100
• SDR-C85300
• SNK-B73047
• SDH-B74086
• SDH-C73043
• SDR-C73303
• SDH-C74043DF
• SDR-C74303N1T
• SDR-B74301

Image 5.1: The remote control displayed alongside a partial list of compatible Samsung Wisenet All-In-One System Series.

Image 5.2: An illustration showing the remote control's compatibility with a range of Samsung Wisenet security camera systems.

6. Maintenance

6.1 Battery Replacement

When the remote control's performance diminishes or it stops responding, replace the AAA batteries. Always replace both batteries at the same time with new ones. Do not mix old and new batteries, or different types of batteries.

6.2 Cleaning

To clean the remote control, use a soft, dry cloth. For stubborn dirt, slightly dampen the cloth with water. Avoid using harsh chemicals, abrasive cleaners, or solvents, as these can damage the remote's surface or internal components.

6.3 Storage

Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. If the remote will not be used for an extended period, it is advisable to remove the batteries to prevent leakage.

7. Troubleshooting

If you experience issues with your SOLTECH CCTV Remote Control, refer to the following common troubleshooting steps:

• Remote Not Responding:
  • Check if the batteries are inserted correctly with the correct polarity.
  • Replace the batteries with fresh AAA batteries.
  • Ensure there is a clear line of sight between the remote control and the infrared receiver on your Wisenet DVR/NVR. Obstructions can block the signal.
  • Verify that the remote control is pointed directly at the Wisenet system.
• Intermittent Functionality:
  • This often indicates low battery power. Replace the batteries.
  • Ensure no strong light sources (like direct sunlight or bright fluorescent lights) are interfering with the infrared signal.
• Remote Does Not Control My System:
  • Confirm that your security system is a Samsung Wisenet All-In-One System and is listed as compatible in Section 5.1. This remote is specifically designed for these systems and may not work with other brands or models.
  • As this remote requires no additional setup, if it is not working with a confirmed compatible system after battery replacement, contact customer support.

8. Specifications

Image 8.1: The remote control with its physical dimensions (length, width, thickness) indicated.

9. Warranty and Support

For information regarding product warranty, please refer to the documentation provided with your purchase or contact the seller directly. The seller for this product is SOLTECH America.

For further assistance or technical support, please reach out to the manufacturer or seller through their official contact channels.