BRP 860202472
Ski-Doo Low Windshield User Manual
Model: 860202472
Product Overview
This manual provides essential information for the installation, operation, and maintenance of the Ski-Doo Low Windshield, model 860202472. This windshield is designed to provide optimal wind deflection and durability for Ski-Doo REV Gen4 models.
Image: Front view of the Ski-Doo Low Windshield (Model 860202472) mounted on a snowmobile, showcasing its dark smoke tint and low-profile design. The windshield is positioned above the headlights, with handlebars visible at the top.
Safety Information
Always prioritize safety during installation and operation. Read all instructions carefully before proceeding. Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation.
- Ensure the snowmobile is turned off and the key is removed before beginning installation.
- Verify all components are securely fastened after installation.
- Do not modify the windshield or its mounting hardware.
- Regularly inspect the windshield for damage or loose components.
Setup and Installation
The Ski-Doo Low Windshield (860202472) is designed for specific Ski-Doo REV Gen4 models. Ensure compatibility before installation. The package includes the windshield and low windshield support.
Required Tools (Not Included):
- Appropriate wrenches or sockets for existing windshield hardware.
- Torque wrench (recommended for precise fastening).
Installation Steps:
- Preparation: Park the snowmobile on a flat, stable surface. Turn off the engine and remove the ignition key.
- Remove Existing Windshield (if applicable): Carefully unbolt and remove the existing windshield from the snowmobile's console. Retain any reusable hardware if instructed by your snowmobile's service manual.
- Position New Windshield: Align the Ski-Doo Low Windshield (860202472) with the mounting points on the snowmobile's console.
- Install Low Windshield Support: Attach the provided low windshield support to the designated points on the windshield and the snowmobile, following the specific instructions for your snowmobile model.
- Secure Hardware: Insert and hand-tighten all bolts and fasteners. Ensure the windshield is properly seated and aligned.
- Final Tightening: Using appropriate tools, tighten all fasteners to the manufacturer's specified torque settings. Avoid over-tightening, which can damage the windshield or mounting points.
- Inspection: After installation, gently attempt to move the windshield to ensure it is securely fastened and does not wobble.
Operating Considerations
Once installed, the Ski-Doo Low Windshield provides enhanced wind deflection. While it is designed for durability, certain operating considerations should be observed:
- Visibility: The dark smoke tint is designed to reduce glare. Ensure your visibility is not impaired, especially in low light conditions.
- Impact: Avoid direct impacts to the windshield. While robust, extreme forces can cause damage.
- Temperature: The windshield is designed to perform in various weather conditions typical for snowmobiling.
Maintenance
Proper maintenance will extend the life and maintain the clarity of your Ski-Doo Low Windshield.
- Cleaning: Clean the windshield regularly with a soft cloth and mild soap and water. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can scratch or damage the surface.
- Drying: Dry with a clean, soft cloth to prevent water spots.
- Inspection: Periodically inspect the windshield for cracks, chips, or loose mounting hardware. Address any issues promptly.
- Storage: When storing the snowmobile for extended periods, consider covering the windshield to protect it from dust and UV exposure.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Windshield is loose or vibrates. | Mounting hardware is not tightened sufficiently. | Check all mounting bolts and tighten them to the recommended torque specifications. |
| Scratches on the windshield surface. | Improper cleaning methods or abrasive contact. | Use only soft cloths and mild soap for cleaning. Avoid wiping dry dirt. Minor scratches may be polished with specialized plastic polish (consult a professional). |
| Reduced visibility. | Dirt, ice, or condensation on the windshield. | Clean the windshield. Ensure proper ventilation to reduce condensation. |
Specifications
| Attribute | Detail |
|---|---|
| Model Number | 860202472 |
| Brand | BRP |
| Height | 13" (32.5 cm) |
| Material | Tempered Glass |
| Color | Dark Smoke |
| Compatibility | Ski-Doo Neo, REV Gen4 models |
| Includes | Low windshield support |
Warranty and Support
For information regarding warranty coverage and customer support, please refer to the official BRP website or contact your authorized Ski-Doo dealer. Keep your proof of purchase for warranty claims.
Manufacturer: BRP
Place of Business: BRP Valcourt QC
Contact: Please visit the official BRP website for contact information and support resources: www.brp.com
Related documents860202472
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.