JESLED 8FT LED Bulbs Light User Manual

Introduction

This manual provides comprehensive instructions for the safe installation, operation, and maintenance of your JESLED 8FT LED Bulbs Light. These high-efficiency LED tubes are designed to replace traditional fluorescent bulbs in various commercial and industrial settings, offering superior brightness and energy savings. Please read this manual thoroughly before installation and retain it for future reference.

Safety Information

WARNING: To prevent electric shock or damage to the product, always turn off power at the circuit breaker before installation or servicing. Installation should be performed by a qualified electrician in accordance with all applicable electrical codes.

• These LED tubes are dual-end powered and require a ballast bypass installation. The existing ballast must be removed or bypassed.
• Do not use with dimmers unless explicitly stated as dimmable. These bulbs are non-dimmable.
• Ensure the lamp body is installed firmly in the fixture.
• Install this item away from radio, remote control door, etc., which may cause EMI (Electromagnetic Interference).
• Product is ETL Listed, ensuring compliance with North American safety standards.
• Do not contain mercury.

Package Contents

Your JESLED 8FT LED Bulbs Light package includes:

• 4 x JESLED 8FT R17D Type B LED Tube Lights
• 1 x User Manual (this document)

Image: Four JESLED 8FT LED tube lights, showing their clear finish and length.

Product Overview and Features

The JESLED 8FT LED Bulbs Light is designed for high performance and energy efficiency, making it an ideal replacement for traditional fluorescent tubes in commercial and industrial environments.

• High Brightness: Illuminates your space with 7200+ lumens.
• Energy Saving: 72W power consumption, equivalent to 150W fluorescent tubes, saving approximately 52% on electricity bills.
• Long Lifespan: Rated for 50,000+ hours, potentially lasting over 20 years depending on usage, significantly reducing maintenance and replacement frequency.
• R17D/HO Base: Designed for R17D/HO base fixtures.
• Dual-Ended Powered: Requires direct wiring to power at both ends after ballast bypass.
• Rotating Ends: Features 180-degree rotatable end caps for flexible light direction.
• V-Shaped Design: Provides a wider beam angle for better light distribution.
• Wide Voltage Compatibility: Operates on AC 100-277 Volts (50/60Hz).
• Color Temperature: 5000K Daylight for a bright, clear illumination.
• Durable Construction: Shatterproof design for enhanced safety and longevity.
• ETL Listed: Certified for safety and quality standards.

Image: An 8ft LED tube light illustrating its length and the 180-degree rotatable end caps.

Image: Close-up of the rotatable end and V-shaped design, demonstrating light output in a warehouse.

Installation Instructions

These JESLED 8FT LED tubes are dual-end powered and require a ballast bypass installation. This means the existing fluorescent ballast must be removed from the fixture. Follow these steps carefully:

1. Turn Off Power: Locate the circuit breaker controlling the lighting fixture and turn off the power. Verify power is off using a voltage tester.
2. Remove Old Fluorescent Tubes: Carefully remove the existing fluorescent tubes from the fixture.
3. Remove/Bypass Ballast: Open the fixture to access the wiring. Disconnect and remove the existing fluorescent ballast. Refer to the wiring diagram below for proper connections.
4. Rewire Fixture:
   • Connect the Live (L) wire from the power source to one end of the fixture's tombstone (socket).
   • Connect the Neutral (N) wire from the power source to the other end of the fixture's tombstone (socket).
   • Ensure all connections are secure using wire nuts or appropriate connectors.
5. Install LED Tubes: Insert the JESLED 8FT LED tubes into the rewired fixture. The R17D base requires pushing the pins into the fixture's sockets and then twisting to lock them in place. Ensure the rotatable ends are adjusted to direct light as desired.
6. Restore Power: Close the fixture cover and turn the power back on at the circuit breaker.

Image: Installation diagram illustrating the ballast bypass wiring and physical removal steps.

Operating Instructions

Once properly installed and power is restored, your JESLED 8FT LED Bulbs Light will operate immediately. These bulbs are designed for instant-on functionality without flickering.

• Simply use the existing wall switch or fixture control to turn the lights ON/OFF.
• These bulbs are non-dimmable. Attempting to use them with a dimmer switch may cause damage or malfunction.
• Adjust the rotatable ends of the tubes to direct light to your desired area.

Maintenance

JESLED 8FT LED Bulbs Lights are designed for minimal maintenance due to their long lifespan and durable construction.

• Cleaning: Ensure power is off before cleaning. Use a soft, dry cloth to wipe the surface of the tubes. Do not use abrasive cleaners or solvents.
• Inspection: Periodically inspect the tubes and wiring for any signs of damage or loose connections. Address any issues promptly.
• No internal user-serviceable parts. Do not attempt to disassemble the tubes.

Troubleshooting

If you experience issues with your JESLED 8FT LED Bulbs Light, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact JESLED customer service for assistance.

Product Specifications

Image: JESLED 8FT LED lights illuminating a warehouse, highlighting key specifications.

Image: A chart comparing different types of JESLED 8FT LED tube lights.

Warranty and Support

JESLED provides a 3-year unlimited customer service warranty for this product. If you are not satisfied or encounter any issues, please contact us for an easy and quick solution.

For further assistance or to explore other JESLED products, visit the official JESLED Store:

Visit the JESLED Store

Image: JESLED customer support information, highlighting 7*24H After-sales Service, 30-Day Exchange Service, and 36-Months Care Plan.