Shineforu 560A02

Download PDF
Contents

Shineforu Ultra-Thin Non-Electric Bidet Attachment

User Manual - Model 560A02

1. Introduction

Thank you for choosing the Shineforu Ultra-Thin Non-Electric Bidet Attachment. This manual provides essential information for the safe installation, operation, and maintenance of your new bidet. Please read this manual thoroughly before installation and keep it for future reference.

Shineforu bidet attachment installed on a toilet

Figure 1: Shineforu Bidet Attachment installed on a toilet.

This image shows the Shineforu bidet attachment seamlessly integrated under a toilet seat, demonstrating its ultra-thin profile and minimalist design in a bathroom setting.

2. Important Safety Information

  • Always turn off the water supply to the toilet before beginning installation or performing any maintenance.
  • Do not use abrasive cleaners or brushes on the bidet surface or nozzles, as this may cause damage.
  • Ensure all connections are tight to prevent leaks. Do not overtighten.
  • This bidet is designed for use with cold water supply only.
  • Keep out of reach of children unless supervised.

3. Package Contents

Please check that all components are present before beginning installation:

  • Shineforu Bidet Attachment
  • Braided Steel Explosion-Proof Hose
  • Metal T-Adapter
  • Installation Manual (this document)
  • Teflon Tape (for optional use if threads are loose)
Components of the Shineforu bidet attachment including stainless steel interface, braided hose, and T-adapter

Figure 2: Key components of the bidet attachment.

This image displays the durable stainless steel interface thread designed to prevent water leakage, along with the braided steel explosion-proof hose and the metal T-adapter, which are essential for installation.

4. Product Features

The Shineforu Bidet Attachment is designed for comfort and hygiene:

  • Ultra-Thin Design: At just 0.23 inches thick, it ensures compatibility with most toilets and does not significantly raise the toilet seat.
  • Dual Nozzle System: Features separate nozzles for a refreshing rear wash and a gentle feminine wash.
  • Non-Electric Operation: Simple, reliable, and energy-efficient.
  • Nozzle Protection Gate: Keeps nozzles clean and hygienic when not in use.
  • Durable Construction: Equipped with a metal water inlet for a secure connection.
Shineforu ultra-thin bidet design showing 0.23 inch thickness and compatibility

Figure 3: Ultra-thin design of the bidet.

This image highlights the ultra-thin profile of the Shineforu bidet, measuring only 0.23 inches, ensuring it fits smoothly under the toilet seat without causing it to lift significantly. It also indicates compatibility with most two-piece toilets.

5. Installation Guide

Installation typically takes about 15 minutes. No special tools are required.

  1. Close the Water Valve: Locate the water supply valve behind your toilet and turn it clockwise to shut off the water supply.
  2. Drain the Water from the Tank: Flush the toilet to empty the tank and bowl. Hold the flush handle down to ensure as much water as possible drains out.
  3. Remove Toilet Seat: Lift the hinge covers and unscrew the bolts holding the toilet seat to the toilet bowl. Remove the toilet seat.
  4. Fix the Bidet to the Toilet: Place the bidet attachment on the toilet rim, aligning the bidet's mounting holes with the toilet's bolt holes. Reinstall the toilet seat on top of the bidet attachment and tighten the bolts.
  5. Install the T-Adapter: Disconnect the existing water supply hose from the toilet tank's fill valve. Connect the T-adapter to the fill valve. Then, reconnect the original water supply hose to the bottom of the T-adapter.
  6. Connect the Hose: Connect one end of the provided braided steel hose to the side of the T-adapter and the other end to the water inlet on the bidet attachment. Ensure all connections are hand-tight. If any connection feels loose, you may use the provided Teflon tape (wrap 2-3 times clockwise around the threads).
  7. Restore Water Supply: Slowly open the water supply valve by turning it counter-clockwise. Check for any leaks. If leaks occur, tighten the connections slightly.
Step-by-step installation guide for the bidet attachment

Figure 4: Easy installation steps.

This diagram illustrates the five key steps for installing the bidet: 1. Close the water valve, 2. Drain water from the tank, 3. Fix the bidet to the toilet, 4. Install the T-adapter, and 5. Connect the hose, providing a clear visual guide for users.

6. Operating Instructions

The bidet is easy to operate using the control knob:

  • The red dot in the middle indicates the OFF position.
  • Gentle Feminine Wash: Gently turn the knob to the left to activate the feminine wash mode. The water pressure increases as you turn the knob further.
  • Refreshing Rear Wash: Gently turn the knob to the right to activate the rear wash mode. The water pressure increases as you turn the knob further.

Caution: Turning the knob too quickly or too far can result in high water pressure, which may cause discomfort or injury. Always start with a low setting and gradually increase pressure as desired.

Bidet operation showing gentle feminine wash and refreshing rear wash modes

Figure 5: Dual nozzle operation.

This image illustrates the two primary wash modes: the Gentle Feminine Wash, activated by rotating the control knob to the left, and the Refreshing Rear Wash, activated by rotating the knob to the right. Both modes show water streams from the respective nozzles.

7. Maintenance and Cleaning

  • Regular Cleaning: Clean the exterior of the bidet with a soft cloth and mild soap or a non-abrasive bathroom cleaner. Rinse thoroughly with water.
  • Nozzle Cleaning: The bidet features a nozzle protection gate. To clean the nozzles, gently pull them down or activate a wash cycle briefly to expose them. Use a soft brush (like a toothbrush) and mild soap to clean the nozzles. Rinse thoroughly.
  • Do Not Use: Avoid using harsh chemicals, abrasive cleaners, or stiff brushes, as these can damage the bidet's finish or nozzles.

8. Troubleshooting

ProblemPossible CauseSolution
Water leakage from connectionsLoose connections; missing or improperly seated rubber washers; damaged threads.Ensure all connections are hand-tight. Check that rubber washers are correctly seated. If threads are loose, apply Teflon tape (2-3 wraps clockwise). Do not overtighten.
No water or low water pressureWater supply valve is closed; kinked hose; clogged nozzle.Ensure the water supply valve is fully open. Check the hose for kinks. Clean the nozzles as described in the Maintenance section.
Nozzles not retracting fullyDebris on nozzles or nozzle mechanism.Clean the nozzles and the area around them thoroughly.

9. Specifications

FeatureDetail
Model Number560A02
BrandShineforu
Dimensions (L x W x H)41.91 x 7.95 x 18.47 cm (16.5 x 3.13 x 7.27 inches)
Weight660 grams (1.46 lbs)
MaterialABS
ColorSilver/White
Power SourceNon-electric (water pressure powered)
Nozzle TypeDual (Rear & Feminine Wash)

10. Warranty and Support

Your Shineforu Bidet Attachment is covered by an 18-month warranty, effective from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.

If you encounter any problems or have questions regarding your bidet, please do not hesitate to contact our customer support. We are committed to ensuring your satisfaction.

For support, please refer to the contact information provided by your retailer or on the official Shineforu website.

© 2023 Shineforu. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.