Introduction
Thank you for choosing the Total Tools TABLI20018 Lithium-ion Blower. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new blower. Please read this manual thoroughly before first use and keep it for future reference.
Image: Total Tools TABLI20018 Lithium-ion Blower, showing the main unit with the nozzle attached.
Important Safety Instructions
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and personal injury. Read all instructions before using this product.
- Personal Safety: Always wear eye protection, hearing protection, and sturdy footwear. Do not operate the blower while barefoot or wearing open-toed sandals.
- Work Area: Keep the work area clean and well-lit. Do not operate in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Electrical Safety: This appliance is battery-powered. Ensure the battery pack is fully charged before use. Do not expose the battery pack or blower to rain or wet conditions.
- Children and Bystanders: Keep children and bystanders away while operating the blower.
- Proper Use: Use the blower only for its intended purpose, which is to move leaves, dirt, and debris. Do not point the nozzle at people or animals.
- Maintenance: Disconnect the battery pack before performing any adjustments, changing accessories, or storing the blower.
Product Components
Familiarize yourself with the parts of your Total Tools TABLI20018 blower before operation.
- Blower Unit (Motor Housing and Handle)
- Blower Nozzle
- Battery Compartment (Battery and charger sold separately)
- On/Off Trigger
- Speed Control Switch
Image: Total Tools TABLI20018 Blower, illustrating the P20S 20V system and indicating that battery and charger are sold separately.
Setup and Assembly
Follow these steps to prepare your blower for use.
- Unpacking: Carefully remove all components from the packaging. Inspect for any damage.
- Attach the Blower Nozzle: Align the blower nozzle with the outlet on the main blower unit. Push and twist until it locks securely into place. Ensure it is firmly attached before operation.
- Install Battery Pack: Ensure the battery pack is fully charged. Slide the charged battery pack into the battery compartment on the blower handle until it clicks into place. Ensure it is seated correctly.
Image: Side view of the Total Tools TABLI20018 Blower, showing the main unit without the nozzle, highlighting the handle and battery slot.
Operating Instructions
Before operating, ensure you have read and understood all safety instructions.
- Starting the Blower: With the battery installed, press the On/Off trigger to start the blower.
- Adjusting Speed: If your model has a speed control switch, adjust it to the desired airflow for the task. The blower features 2 speeds.
- Operating Technique:
- Hold the blower firmly with one hand on the handle.
- Sweep the nozzle from side to side, directing debris away from yourself and others.
- Work in small sections to maintain control.
- Avoid blowing debris towards open windows, cars, or water sources.
- Stopping the Blower: Release the On/Off trigger to stop the blower.
- After Use: Remove the battery pack from the blower after each use to prevent accidental starting and for safe storage.
Maintenance and Storage
Regular maintenance ensures optimal performance and extends the life of your blower.
- Cleaning:
- Always remove the battery pack before cleaning.
- Wipe the exterior of the blower with a damp cloth. Do not use strong detergents or solvents.
- Clear any debris from the air intake vents and blower nozzle to ensure proper airflow.
- Storage:
- Store the blower in a dry, well-ventilated area, out of reach of children.
- Remove the battery pack before storing for extended periods.
- Store the battery pack in a cool, dry place, away from direct sunlight and extreme temperatures.
Image: Angled view of the Total Tools TABLI20018 Blower, showing the air intake grille on the side of the motor housing.
Troubleshooting
Refer to this section for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Blower does not start. | Battery not installed correctly or discharged. | Ensure battery is fully charged and properly seated. |
| Reduced airflow. | Air intake or nozzle blocked by debris. | Remove battery, then clear any obstructions from the air intake and nozzle. |
| Blower stops during operation. | Battery overheated or discharged. | Allow battery to cool down or replace with a fully charged battery. |
| Excessive vibration. | Loose nozzle or internal debris. | Check nozzle attachment. Remove battery and inspect for internal debris. If problem persists, contact customer support. |
Specifications
Technical data for the Total Tools TABLI20018 Lithium-ion Blower.
| Feature | Detail |
|---|---|
| Model | TABLI20018 |
| Brand | Total |
| Voltage | 20 Volts |
| Speed | 18000 RPM |
| Air Volume | 2.7 m³/min |
| Style | Handheld |
| Power Source | Battery Powered (Lithium-ion) |
| Item Weight | 739 g (1.63 Pounds) |
| Product Dimensions | 10 x 10 x 10 cm (approximate) |
| Special Features | Lightweight, 2-speed |
| Included Components | Blower unit only (battery and charger sold separately) |
Image: Size comparison of the Total Tools TABLI20018 Blower, indicating a length of approximately 17 cm (7.0 inches).
Warranty and Support
Specific warranty information for the Total Tools TABLI20018 blower is typically provided with the product packaging or can be obtained from the point of purchase. For technical support, service, or to inquire about replacement parts, please contact Total Tools customer service or visit their official website.
