Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Electrolux LFP226S Built-in Telescopic Kitchen Hood. Please read these instructions carefully before using the appliance and keep them for future reference.
Important Safety Information
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons.
- Ensure the appliance is correctly installed and earthed by a qualified person.
- Do not operate the hood if it is damaged or malfunctioning.
- Maintain a minimum distance between the hob and the lower part of the hood as specified in the installation section. For gas hobs, this is typically 650 mm, and for electric hobs, 420 mm.
- Clean grease filters regularly to prevent fire hazards.
- Do not flambé under the range hood.
- Ensure adequate ventilation in the room when the range hood is used simultaneously with appliances burning gas or other fuels.
- Disconnect the appliance from the power supply before any cleaning or maintenance.
Setup and Installation
The Electrolux LFP226S is a built-in telescopic kitchen hood designed for under-cabinet mounting. Proper installation is crucial for optimal performance and safety.
Installation Dimensions
Refer to the diagram below for precise measurements required for installation. Ensure sufficient space is available in your cabinet for the hood's dimensions.
Image: Detailed diagram showing the dimensions for installing the Electrolux LFP226S telescopic kitchen hood. Key measurements include the overall width (502mm), depth (265mm), and height (179mm). The ducting outlet has a diameter of 150mm. The diagram also indicates minimum clearance requirements from the cooking surface: 420mm for electric hobs and 650mm for gas hobs.
- Cabinet Opening: The required opening in the cabinet for the hood body is approximately 502mm wide and 265mm deep.
- Ducting: The hood features a 150mm diameter ducting outlet for exhaust. Ensure proper connection to an external ventilation system.
- Minimum Clearance: Maintain a minimum distance of 420mm between the hood and an electric hob, and 650mm for a gas hob, to ensure safe operation and efficient extraction.
- Mounting: The hood is designed for under-cabinet mounting. Secure it firmly according to the provided mounting points.
Operating Instructions
The Electrolux LFP226S features intuitive controls for fan speed and lighting.
Control Panel
The control panel is located on the front of the hood, accessible when the telescopic section is pulled out.
Image: A detailed view of the control panel for the Electrolux LFP226S kitchen hood. It features four push buttons: '2' for medium fan speed, '3' for high fan speed, '0|1' for turning the fan on/off at low speed, and a light bulb icon for controlling the hood's illumination.
- Fan Speed Control:
- Press '0|1' to turn the fan on at low speed (Speed 1). Press again to turn off.
- Press '2' for medium fan speed.
- Press '3' for high fan speed.
- To switch between speeds, simply press the desired speed button.
- Light Control:
- Press the button with the light bulb icon to turn the hood lights on.
- Press the light bulb icon button again to turn the lights off.
- Telescopic Function: Pull the front panel of the hood outwards to activate the telescopic function and expose the filters and controls. Push it back in to retract.
Maintenance and Cleaning
Regular maintenance ensures the longevity and efficiency of your kitchen hood. Always disconnect the power supply before performing any maintenance.
Cleaning Grease Filters
The hood is equipped with baffle filters designed to trap grease. These should be cleaned regularly, typically every 2-4 weeks depending on usage, to maintain optimal performance and prevent fire hazards.
Image: A close-up view of the metal baffle filters within the Electrolux LFP226S kitchen hood. The image highlights the mesh structure of the filters and a small handle or latch mechanism used for easy removal and reinstallation during cleaning.
- Removal: Locate the latch or handle on each filter. Pull or slide the latch to release the filter and carefully remove it.
- Cleaning: Wash the filters by hand in hot water with a mild detergent, or in a dishwasher on a low-temperature cycle. Ensure they are completely dry before reinstallation.
- Reinstallation: Insert the dry filters back into their slots, ensuring they click securely into place.
Replacing Lights
The hood uses LED type light sources. If a light needs replacement, ensure the hood is disconnected from power.
Image: A detailed shot of the LED light panel integrated into the Electrolux LFP226S kitchen hood. The light is covered by a translucent diffuser, providing even illumination over the cooking area.
- Access: Carefully remove the light cover or diffuser.
- Replacement: Replace the faulty LED module with an original spare part from Electrolux or an authorized service center. Do not attempt to replace individual LED bulbs.
- Reassembly: Securely reattach the light cover.
Exterior Cleaning
Clean the exterior surfaces of the hood with a soft cloth and a non-abrasive cleaner. Avoid harsh chemicals or abrasive materials that could damage the silver finish.
Troubleshooting
Before contacting service, check the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not operate. | No power supply. | Check if the appliance is plugged in and the circuit breaker is on. |
| Poor extraction performance. | Grease filters are clogged. | Clean or replace the grease filters. |
| Poor extraction performance. | Ducting is blocked or improperly installed. | Check ducting for obstructions and ensure correct installation. |
| Lights not working. | LED module faulty. | Replace the LED module (refer to Maintenance section). |
| Excessive noise during operation. | Loose components or improper installation. | Ensure all mounting screws are tight and filters are correctly seated. |
If the problem persists after checking these points, please contact Electrolux customer service or a qualified technician.
Specifications
Technical details for the Electrolux LFP226S Built-in Telescopic Kitchen Hood:
- Model Number: LFP226S
- Type: Built-in Telescopic Kitchen Hood
- Color: Silver
- Airflow Capacity: 330 m³/h (Cubic meters per hour)
- Noise Level: 65 Decibels
- Control Type: Push Button
- Light Source Type: LED
- Filter Type: Baffle (Déflecteur)
- Mounting Type: Under-cabinet (Montage sous armoire)
- Weight: 7 Kilograms
- Manufacturer: Electrolux
Warranty and Support
Specific warranty details are not provided in this document. For warranty information, technical support, or to order spare parts, please refer to the warranty card included with your product or visit the official Electrolux website. You may also contact Electrolux customer service directly.
Availability of Spare Parts: Information regarding the availability of spare parts is not available in the provided product data. Please contact Electrolux customer support for details.
