BETAFPV VR03 FPV Goggles User Manual

1. Introduction

The BETAFPV VR03 FPV Goggles are designed to provide an immersive First Person View experience for FPV racing drones and model airplanes. Featuring a 4.3-inch 800x480px HD LCD screen, these goggles offer clear visuals without distortion. The integrated DVR function allows for recording and replaying flight footage, enhancing the user experience. The goggles operate on the 5.8GHz frequency band with 48 channels and support NTSC/PAL video formats.

Image: Front view of the BETAFPV VR03 FPV Goggles, showcasing their compact design.

2. Package Contents

Verify that all items are present in the package:

• BETAFPV VR03 FPV Goggles
• Replaceable 5.8G 3dBi Omnidirectional Antenna
• Adjustable Headband
• USB Type-C Charging Cable
• User Manual

Image: The VR03 FPV Goggles, its packaging, and included accessories like the headband and user manual.

3. Product Diagram

Familiarize yourself with the components and controls of the VR03 FPV Goggles.

Image: A detailed diagram highlighting the Type-C Port, Charging Indicator, Power On/Off switch, Recording Indicator, Recording Button, Channel Up (CH+), Band Up (Band+), Search button, Micro SD Card Slot, and Antenna.

• Type-C Port: For charging the internal battery.
• Charging Indicator: Shows charging status.
• Power On/Off Switch: Controls the main power.
• Recording Indicator: Lights up when DVR recording is active.
• Recording Button: Initiates or stops DVR recording.
• CH+ Button: Changes the video channel.
• Band+ Button: Changes the video band.
• Search Button: Activates the auto-search function for video signals.
• Micro SD Card Slot: For inserting a Micro SD card (not included) for DVR recording.
• Antenna: Replaceable 5.8G 3dBi omnidirectional antenna for video reception.

4. Setup

4.1. Antenna Installation

1. Locate the antenna connector on the side of the goggles.
2. Carefully screw the provided 5.8G 3dBi omnidirectional antenna onto the connector until it is finger-tight. Do not overtighten.

4.2. Charging the Battery

1. Connect the USB Type-C charging cable to the Type-C port on the goggles.
2. Connect the other end of the cable to a compatible USB power source (e.g., computer USB port, USB wall adapter).
3. The Charging Indicator will illuminate during charging and turn off when fully charged.
4. A full charge provides approximately 2 hours of normal operation or 1 hour and 10 minutes in recording mode.

Image: Illustration showing the built-in 2000mAh battery and its approximate operating times for normal and recording modes.

4.3. Inserting a Micro SD Card

1. Locate the Micro SD Card Slot on the side of the goggles.
2. Insert a Micro SD card (Class 10 or higher recommended, up to 64GB) with the contacts facing down until it clicks into place.
3. To remove, gently push the card in until it springs out.

5. Operating Instructions

5.1. Powering On/Off

• To power on, slide the Power On/Off switch to the "On" position.
• To power off, slide the Power On/Off switch to the "Off" position.

5.2. Automatic Frequency Search

The goggles feature a fast auto-search function to find the strongest video signal.

1. Ensure your FPV drone or video transmitter is powered on and transmitting.
2. Press the Search Button (S button) on the goggles.
3. The goggles will scan all 48 channels and automatically lock onto the channel with the strongest signal within approximately 3 seconds.

Image: Visual representation of the one-key auto-search function, showing the button, band results, and instant display.

5.3. Manual Band and Channel Selection

If automatic search does not yield the desired result, you can manually select the band and channel.

1. Press the Band+ Button to cycle through the available frequency bands (A, B, E, F, R, L).
2. Once the desired band is selected, press the CH+ Button to cycle through the channels (1-8) within that band.
3. Refer to the frequency table below for specific channel frequencies.

Image: A table detailing the 5.8GHz frequency bands and their corresponding channels in MHz.

5.4. DVR Recording

The VR03 FPV Goggles allow you to record your flight footage directly to a Micro SD card.

1. Ensure a Micro SD card is inserted into the goggles.
2. With the goggles powered on and receiving a video signal, press the Recording Button (red dot button).
3. The Recording Indicator will illuminate, indicating that recording has started.
4. To stop recording, press the Recording Button again. The indicator will turn off.
5. Recorded videos are saved as AVI files on the Micro SD card.

Image: A view through the goggles showing an FPV feed with on-screen display elements, illustrating the DVR recording capability.

5.5. Playback

You can review recorded footage directly on the goggles.

1. While in normal viewing mode, press and hold the Recording Button for approximately 3 seconds to enter playback mode.
2. Use the CH+ and Band+ buttons to navigate through recorded files.
3. Press the Recording Button briefly to play or pause a selected video.
4. To exit playback mode, press and hold the Recording Button again for 3 seconds.

6. Maintenance

6.1. Cleaning

• Use a soft, dry cloth to clean the exterior of the goggles.
• For the LCD screen, use a specialized screen cleaning cloth and solution if necessary, applying gently to avoid scratches.
• Keep the foam faceplate clean and dry.

6.2. Battery Care

• Avoid fully discharging the Lithium Polymer battery.
• Store the goggles with the battery partially charged (around 50%) if not used for extended periods.
• Do not expose the battery to extreme temperatures.

6.3. Storage

• Store the goggles in a cool, dry place away from direct sunlight.
• Protect the screen from pressure or sharp objects.

7. Troubleshooting

• No Video Signal:
  • Ensure the FPV drone/video transmitter is powered on and transmitting.
  • Verify the antenna is securely attached to the goggles.
  • Perform an automatic frequency search.
  • Manually cycle through bands and channels to find the correct frequency.
  • Check for obstructions between the drone and goggles.
• Poor Video Quality/Static:
  • Ensure the antenna is properly connected and undamaged.
  • Try a different channel or band.
  • Reduce the distance between the drone and goggles.
  • Minimize interference from other 5.8GHz devices.
• DVR Not Recording:
  • Ensure a Micro SD card is inserted correctly.
  • Check if the Micro SD card has sufficient free space.
  • Verify the Micro SD card is formatted correctly (FAT32 recommended).
  • Ensure the card is Class 10 or higher.
  • Reformat the Micro SD card if issues persist (this will erase all data).
• Goggles Not Powering On:
  • Ensure the battery is charged. Connect to a charger and check the Charging Indicator.
  • Verify the power switch is in the "On" position.

8. Specifications

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact BETAFPV directly using the information below. Keep your purchase receipt as proof of purchase.

• Manufacturer: Shenzhen Baida Moxing Co., Ltd.
• Website: betafpv.com
• Email Support: support@betafpv.com

For additional resources and community engagement, you can visit BETAFPV's social media channels:

• Instagram: @betafpv
• Facebook: BETAFPV
• YouTube: BETAFPV Official