1. Introduction
This user manual provides essential information for the safe and efficient operation of your Havit Lighting 30W 12V DC IP20 Triac Indoor Dimmable LED Driver. Please read this manual thoroughly before installation and use, and retain it for future reference.
The Havit Lighting 30W 12V DC IP20 Triac Indoor Dimmable LED Driver is designed to provide stable 12V DC power for LED lighting applications, featuring Triac dimming capabilities for adjustable light output. It comes complete with a flex and plug for easy installation in indoor environments.
2. Safety Information
WARNING: Electrical Shock Hazard. Installation should only be performed by a qualified electrician.
- Ensure the main power supply is disconnected before installation, maintenance, or troubleshooting.
- This LED driver is rated IP20, meaning it is suitable for indoor use only. Do not expose to moisture, water, or high humidity.
- Do not exceed the maximum load of 24W. The minimum load is 3W.
- Ensure proper ventilation around the driver to prevent overheating.
- Do not attempt to open or modify the driver. There are no user-serviceable parts inside.
- Connect the input (240V AC) and output (12V DC) correctly as indicated on the unit.
3. Product Features
- Triac dimmable LED driver, allowing for smooth dimming from 10% to 100%.
- Complete with Flex and Plug for convenient connection to a standard power outlet.
- Easy to install design.
- Suitable for indoor area use only (IP20 rated).
- Enhances your home lighting with a stylish, modern atmosphere.
- Constant Voltage output (12V DC).
4. Setup and Installation
Follow these steps for proper installation of the LED driver:
- Preparation: Ensure the main power supply to the installation area is turned off at the circuit breaker.
- Mounting: Position the LED driver in a suitable indoor location, ensuring adequate ventilation. The driver dimensions are approximately 155mm (L) x 54mm (W) x 20mm (H). Refer to the dimension diagram below for precise measurements and mounting points.
Figure 1: Technical drawing showing the dimensions of the LED driver, including length (155mm), width (54mm), and height (20mm), along with input and output port locations and mounting hole details (Ø3mm).
- Input Connection: Plug the integrated flex and plug into a standard 240V AC power outlet.
- Output Connection: Connect your 12V DC LED lighting fixtures to the output terminals of the driver. Ensure correct polarity (+ to + and - to -). The output is 12V DC at 2.5A, providing 30W of power.
Figure 2: Front view of the Havit Lighting LED Driver, showing the input cable, output terminals, and product labeling with specifications such as model number (HV9660-12V30W), input voltage (200-240V AC), and output voltage (12V DC).
- Power On: Once all connections are secure, restore power at the circuit breaker.
5. Operating Instructions
This LED driver is designed for use with Triac dimmers (leading edge and trailing edge). To operate:
- Ensure the LED driver is correctly installed and powered on.
- Use a compatible Triac dimmer switch connected to the 240V AC input circuit to adjust the brightness of the connected LED lights.
- The dimming range is typically from 10% to 100%. Adjust the dimmer control to achieve the desired light level.
Note: The quality of dimming performance may vary depending on the specific Triac dimmer used and the connected LED load. For optimal performance, use high-quality, compatible dimmers.
6. Maintenance
The Havit Lighting LED Driver requires minimal maintenance. Follow these guidelines:
- Keep the driver clean and free from dust. Use a soft, dry cloth for cleaning.
- Do not use liquid cleaners or abrasive materials.
- Ensure that the ventilation openings are not obstructed.
- Regularly check connections for tightness and signs of wear.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No light output from LEDs. |
|
|
| LEDs flicker or dim erratically. |
|
|
| Driver is hot to the touch. |
|
|
If problems persist after following these steps, please contact customer support.
8. Specifications
| Model Number | HV9660-12V30W |
| Input Voltage | 240V AC |
| Output Voltage | 12V DC |
| Output Power | 30W |
| Recommended Maximum Load | 24W |
| Minimum Load | 3W |
| Dimming Type | Triac (Leading edge & Trailing edge) |
| Dimming Range | 10% - 100% |
| IP Rating | IP20 (Indoor Use Only) |
| Dimensions (L x W x H) | 15.5 x 5.4 x 2 cm |
| Weight | 300 Grams |
| Certification | UL |
9. Warranty Information
The Havit Lighting 30W 12V DC IP20 Triac Indoor Dimmable LED Driver comes with a 3 Years Replacement Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
The warranty does not cover damage caused by improper installation, misuse, abuse, unauthorized modifications, or exposure to conditions beyond the specified IP20 rating (e.g., water damage).
To make a warranty claim, please retain your proof of purchase and contact your retailer or Havit Lighting customer support.
10. Customer Support
For technical assistance, troubleshooting, or warranty inquiries, please contact Havit Lighting customer support:
- Website: www.havitlighting.com.au (Example link, actual link may vary)
- Email: support@havitlighting.com.au (Example email, actual email may vary)
- Phone: Please refer to the Havit Lighting website for local contact numbers.
When contacting support, please have your product model number (HV9660-12V30W) and proof of purchase readily available.
